Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 131-1470

FormNo.3385-772RevB

StripingKit

2014or2015GrandStand

Mowers

ModelNo.131-1470

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemower.

Mountingbracket2

Carriagebolt(3/8x1inch)

Flangenut(3/8inch)

Installthemountingbrackets.

Spring

Clevispin

Hairpincotter2

Installtherollerassemblytostriper

bracketmounts.

Nopartsrequired

–

Connectthechains.

PreparingtheMower

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

4.Thoroughlycleanthemowerdeck.Removealldebris

toensurethatthekitwilltproperly.

5.Repairallbentordamagedareasandreplaceany

missingparts.

6.Raisetheplatformandverifythelatchissecurely

engagedtoholdtheplatformup.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3385-772*B

Summary of content (8 pages)

PAGE 1
Form No. 3385-772 Rev B Striping Kit 2014 or 2015 GrandStand® Mowers Model No. 131-1470 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Qty.
PAGE 2
Installing the Mounting Brackets 1 2 Parts needed for this procedure: 2 Mounting bracket 2 Carriage bolt (3/8 x 1 inch) 2 Flange nut (3/8 inch) 3 g026595 g026595 Figure 2 Shown with narrow base mower 1. Flange nut (3/8 inch) Procedure 3. Carriage bolt (3/8 x 1 inch) 2. Mounting bracket 1. Install the mounting brackets to the outside holes for narrow base mowers (48 inch and 52 inch mowers) and the inside holes for wide base mowers (60 inch mowers) (Figure 1).
PAGE 3
2 1 3 4 4 1 2 2 5 G026602 g026602 Figure 3 1. Left-spring long finger 4. Hairpin-cotter 2. Clevis pin 5. Roller assembly 3 4 3 3. Right-spring long finger g026656 g026656 Figure 5 2. Position the roller assembly into the striper mounting brackets (Figure 4). 3. Insert the clevis pin through the striper mounting bracket, roller mount and spring and secure it with a hairpin cotter (Figure 4). 1. Top of the roller assembly 3. Short-spring finger under mounting bracket 2.
PAGE 4
g011307 Figure 6 1. Left lift handle 3. Right lift handle 2. Platform down 4. Roller 3. Snap the chain end into the hole in the lower front side plate of the platform. Repeat for the opposite side (Figure 7). g010976 Figure 7 1. Hole in the lower front side 2.
PAGE 5
Operation • Stiff grass where wheel tracks are less visible will usually Raising the Roller • Cool season grass types found in northern areas are With the platform down, raise the roller up and rotate the lift handle over the platform (Figure 8). • Warm season grass types found in southern areas will produce poor striping. usually good for striping. usually produce less pronounced striping.
PAGE 6
Driving the machine to different cutting areas • Bagging can display heavy wheel tracks, reducing the effect of striping. • Mulching will often display excellent contrast, enhancing • Raise the roller and the deck and drive along a previous the effect of striping. cut path to transport from one area of the property to another section. The landscape can promote or hinder striping • A nice striping pattern can be ruined by driving across the pattern.
PAGE 7
Notes:
PAGE 8