Installation Instructions

ManualsBrandsToro ManualsGreens RollerRoller Mount Kit, GreensPro 1200 Greens Roller

FormNo.3386-959RevA

RollerMountKit

GreensPro

™

1200GreensRoller

ModelNo.131-1619

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Rollersupport2

Bolt(M10x35mm)

Grommet

Bolt(M10x40mm)

Locknut(M10)

Washer(M10)

Installthekit.

PreparingtheMachine

1.Removetherollercylindersfromthesteeringheads.

Note:Retainallofthehardwareforlaterinstallation.

Figure1

1.Bolt(spring)

5.Rollercylinder

2.Nut

6.Washer(roller)

3.Washer(spring)7.Splitwasher

4.Locknut

8.Bolt(roller)

2.Removethebolts,thenuts,andthewasherssecuring

thespringstoeachsteeringhead.

3.Removethesteeringheadsfromthemachineasshown

inFigure2.

Note:Retainthewashersandthesteeringroller

assemblies.Discardthenutsandthebolts.

Figure2

1.Washer(16)—retain3.Steeringheads

2.Nut(8)—discard4.Bolt(8)—discard

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3386-959*A

Summary of content (4 pages)

PAGE 1
Form No. 3386-959 Rev A Roller Mount Kit GreensPro™ 1200 Greens Roller Model No. 131-1619 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine.
PAGE 2
4. Cut off the existing roller supports 2.5 to 5.7 cm (1 to 2-1/4 inches) from the frame (Figure 3). Important: Ensure that the existing supports do not obstruct the installation of the new supports. Figure 4 1. 20.4 cm (8.04 inches) 3. Frame rib 2. Roller supports Figure 3 1. 2.5 to 5.7 cm (1 to 2-1/4 inches) 5. Grind the cut edges smooth and paint the bare metal. 6. Drill out the ends of all cracks and grind the cracks to allow for weld penetration. 7.
PAGE 3
7. Using the 8 bolts (M10 x 40 mm), 8 locknuts (M10), and the 8 previously removed washers, secure a new roller support to each of the previously removed roller bearings and smoothing rollers (Figure 6). Figure 8 Some parts not shown 1. Bolt—M10 x 35 mm (8) 3. Locknut—M10 (8) 2. Washer—M10 (16) Figure 6 1. Locknut (8) 4. Steering bearing assembly 2. Washer (existing), 16 5.
PAGE 4
1 2 2 1 G025386 Figure 10 1. Joints 2. Short roller tube Figure 12 11. Connect each of the 2 springs to the appropriate steering head, using the hardware previously removed; refer to Figure 11. 1. Straightedge 3. Rear roller assembly 2. Front roller assembly Note: Keep part of the shank on each bolt exposed. Figure 13 1. Jam nut 2. Threaded rod 13. Adjust the steering rod lengths as necessary (Figure 13).