Use and Care Manual

ManualsBrandsToro ManualsMulching & StripingTimeCutter 54 in. Striping Kit

FormNo.3392-373RevB

54inStripingKit

Zero-Turn-RadiusRidingMower

ModelNo.131-4165

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removethemowerdeck.

Bracket

Rubbercap

Speednut

Wiper1

Bolt(1/4x3/4inch)

Locknut(1/4inch)

Washer

Installthestripingkit.

Nopartsrequired

–

Installthemower.

RemovingtheMowerDeck

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceanddisengagethe

blade-controlswitch.

2.Ensuretheparkingbrakeisengaged,stoptheengine,

removethekey,andwaitforallmovingpartstostop

beforeleavingtheoperatingposition.

3.Removethemowerdeckfromthemachine.Refer

totheRemovingtheMowersectionintheOperator's

ManualortheappropriatesectionoftheServiceManual.

WARNING

Thespringisundertensionwheninstalled

andcancausepersonalinjury.

Becarefulwhenremovingthemowerbeltand

deck.

4.Slidethemowerdeckoutfromunderneaththe

machine.

5.Removethedeckspringfromtheidlerarm.

Important:Makenoteofthedeckspring

orientation.Itmustbeinstalledinthissamehook

endorientation.

InstallingtheStripingkit

Partsneededforthisprocedure:

Bracket

Rubbercap

Speednut

1Wiper

Bolt(1/4x3/4inch)

Locknut(1/4inch)

Washer

OriginalInstructions(EN)PrintedintheUSA.

AllRightsReserved

*3392-373*B

Summary of content (4 pages)

PAGE 1
Form No. 3392-373 Rev B 54in Striping Kit Zero-Turn-Radius Riding Mower Model No. 131-4165 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Remove the mower deck. 2 Bracket Rubber cap Speed nut Wiper Bolt (1/4 x 3/4 inch) Locknut (1/4 inch) Washer 5 5 5 1 10 5 5 Install the striping kit. 3 No parts required – Install the mower. 4.
PAGE 2
Installing the Stripping Kit Note: The information in Operation (page 3) can help you choose which set of holes/wiper height to use to install the wiper assembly. 1. Assemble 5 brackets as shown in Figure 1 using 5 sets of rubber caps, speed nuts, and brackets. Figure 1 1. Bracket Figure 3 3. Rubber cap 2. Speed nut 1. Bolt (1/4 x 3/4 inch) 3. Wiper 2. Washer 4. Bracket 2. Clean the rear edge of the mower deck 5. Use 5 bolts (1/4 x 3/4 inch) and 5 washers to secure the wiper to the deck. 3.
PAGE 3
Operation Adjusting the Height Important: Applying excessive downward pressure with the striping bar may damage turf and the striping kit. Important: Raise the mower deck to the transport position when not in use to avoid damaging the wiper. Important: Avoid obstacles that can damage the kit. Temporarily lift the deck to transport position when performing turns or moving in reverse.
PAGE 4
Viewing Position Training the Lawn for Striping The grass that is bent toward you will appear darker, and the grass that is bent away from you will appear lighter. • On a new property during weeks 1 and 2, you may need to follow the exact same pattern and direction in the same wheel tracks. This will begin training the grass to bend in the desired direction. • Mowing patterns that generally are parallel to a road will have greater contrast when viewed approaching or leaving the property.