Use and Care Manual

ManualsBrandsToro ManualsMulching & StripingMX TimeCutter 34 in. Striping Kit

FormNo.3392-387RevB

34inStripingKit

Zero-Turn-RadiusRidingMower

ModelNo.131-4167

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Washer-headscrew(5/16x3/4inch,

self-threading)

Mountingbracket2

Stripingbracket

Installthestripingkitbracketassembly.

Hex-headscrew(5/16x3/4inch)

Washer4

Clipnut

Wiper1

Installingthestripingkitwiper.

RemovingtheMowerDeck

1.Parkthemachineonalevelsurfaceanddisengagethe

blade-controlswitch.

2.Engagetheparkingbrake,stoptheengine,removethe

key,andwaitforallmovingpartstostopbeforeleaving

theoperatingposition.

3.Removethemowerdeckfromthemachine.Refer

totheRemovingtheMowersectionintheOperator's

ManualortheappropriatesectionoftheServiceManual.

WARNING

Thebelttensionspringisundertensionwhen

installedandcancausepersonalinjury.

Becarefulwhenremovingthemowerbeltand

deck.

4.Slidethemowerdeckoutfromunderneaththe

machine.

5.Cleanthebackofthemowerdeck.

OriginalInstructions(EN)PrintedintheUSA

AllRightsReserved

*3392-387*B

Summary of content (8 pages)

PAGE 1
Form No. 3392-387 Rev B 34in Striping Kit Zero-Turn-Radius Riding Mower Model No. 131-4167 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Installing the Striping Kit Brackets Note: Align the left edge of the mounting bracket with the left edge of skid and the top edge of the mounting bracket with the top edge of the skid. 3. Mark the outline of the mounting bracket hole onto the skid (Figure 1). Installing the Mounting Brackets 1. Locate the right skid on the rear-facing side of the mower deck as shown in Figure 1. 4. Remove the bracket. Center-punch the center of the outline marked on the skid. 5.
PAGE 3
Installing the Wiper Installing the Mower Note: Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. Installing the Wiper 1. Align the clip nut so that the flat leg of the clip nut faces away from the mower deck (Figure 2). 1. Install the mower belt (Figure 3 ), if removed. Refer to the Replacing the Mower Belt section in the Operator's Manual.
PAGE 4
Operation Adjusting the Height Important: Applying excessive downward pressure with the striping bar may damage turf and the striping kit. To avoid damage to landscaping and the striping bar, avoid close trimming with the striping kit installed. Replace the wiper yearly, or more often as wear requires. Avoid obstacles that can damage the kit. Temporarily lift the deck to the transport position when performing turns or moving in reverse.
PAGE 5
Viewing Position Training the Lawn for Striping The grass that is bent toward you appears darker, and the grass that is bent away from you appears lighter. • On a new property during weeks 1 and 2, you may need to follow the exact same pattern and direction in the same wheel tracks. This begins training the grass to bend in the desired direction. • Mowing patterns that generally are parallel to a road have greater contrast when viewed approaching or leaving the property.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8
Notes: 8