Installation Instructions

ManualsBrandsToro ManualsDrillToro 131-9018

FormNo.3396-948RevA

ZapAlertGroundStakeRelocationKit

2024and4045DirectionalDrill

ModelNo.131-9018

ModelNo.131-9019

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

2024DirectionalDrillbracket1

4045DirectionalDrillbracket1

Grommets

Bolts(M12)

Locknuts(M12)

Junctionblock1

Bolts(M5)

Nuts(M5)

Installthebrackets.

Strikealertcable

Negativebatterycable1

Stake

Bolt(M6)

Flangenut(3/8inch)

Routethecables.

Nopartsrequired

–

Testthezap-alertsystem.

RelocatingtheZap-Alert

Assembly

RemovingtheExistingCableand

Bracket

Parkthemachineonalevelsurfaceandturntheengineoff.

Removethezap-alertcableandbracket(Figure1).

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3396-948*A

Summary of content (4 pages)

PAGE 1
Form No. 3396-948 Rev A ZapAlert Ground Stake Relocation Kit 2024 and 4045 Directional Drill Model No. 131-9018 Model No. 131-9019 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
Installing the Brackets Installing the Brackets for the 4045 Directional Drill Installing the Brackets for the 2024 Directional Drill 1. Install the grommets onto the bracket (Box A of Figure 3). 1. Install the grommets onto the bracket (Box A of Figure 2). Figure 3 4045 Directional Drill Figure 2 2024 Directional Drill 1. Drill holes here 3. Locknuts (M12) 2. Bolts (M12) 4. Bolts (M5) 1. Drill holes here 4. Nuts (M12) 2. Nuts (M5) 5. Bolts (M12) 3. Bolts (M5) 2.
PAGE 3
Routing the Cables Routing the Cables for the 2024 Directional Drill 1. Connect the stake to the negative battery cable using 1 bolt (M6) as shown in Figure 4. Figure 4 1. Bolt (M6) 2. Place the stake in the bracket and wrap the negative-battery cable around the bracket as shown in Figure 5. Figure 6 2024 Directional Drill 4. Route the strike-alert cable as shown in Box C and Box D of Figure 6. 5. Connect the strike-alert cable to the machine using 1 flange nut (3/8 inch) as shown in Box B of Figure 6.
PAGE 4
Routing the Cables for the 4045 Directional Drill Testing the Zap-Alert System Test the zap-alert system; refer to your machine Operator’s Manual. 1. Connect the stake to the negative-battery cable using 1 bolt (M6) as shown in Figure 4. 2. Place the stake in the bracket and wrap the negative-battery cable around the bracket as shown in Figure 7. Figure 7 4045 Directional Drill 3. Connect the strike-alert cable to the junction block using 1 (3/8 inch) flange nut as shown in Box A of Figure 8.