Parts Catalogue

ManualsBrandsToro ManualsUtility VehicleToro 132-3141

 NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain

these Installation Instructions for future reference.

Arctic Cat

Prowler

Installation Instructions - Accessory Kit

Form No. 0453-731

LXC Windshield Kit

(1436-501)

Kit includes:

p/n QTY DESCRIPTION

2441-243 1 Windshield Glass

2441-242 1 Top Sealing Foam

2441-244 2 Gas Spring

2441-241 4 C-Clamp

2441-247 1 Grab Handle

2441-245 1 Grab Catch Support

2441-246 1 Grab Catch

* 2 Machine Screw (M6-10 x 14 mm)

* 2 Machine Screw (M6-1.0 x 16 mm)

* 2 Machine Screw (M6-1.0 x 20 mm)

* 2 Machine Screw (M6-1.0 x 25 mm)

* 2 M6 Fender Washer

* 4 Flange Lock Nut

* 4 Lock Nut (M8-1.25)

* 2 Grab Catch Screws w/Rubber Well Nuts

* 4 Rubber Washer

* 4 Fender Washer

0453-731 1 Instructions

*Included in Hardware Kit (p/n 1436-705)

1. Assemble Grab Catch (B) onto Grab Catch Support (C)

using two Machine Screws (M6-1.0 X 16 mm) (A) and

two Flange Lock Nuts (D) (finger tighten at this time).

See Fig. 1.

Fig. 1

UTV-160A

2. Secure the grab catch support (D) onto the lower center

part of Windshield Assembly using two Machine

Screws (M6-1.0 X 14 mm) (A), two Fender Washers

(#B), and two Rubber Washers (C). See Fig. 2.

Fig. 2

UTV-161A

 NOTE: If Roof Kit (p/n 1436-500) is installed, go

to step 3. If not, go to step 4.

3. Remove and retain the C-clamps securing the roof to

the ROPS tubes; then remove the roof. See Fig. 3.

Fig. 3

UTV-162

Summary of content (3 pages)

PAGE 1
Form No. 0453-731 Arctic Cat® Prowler Installation Instructions - Accessory Kit LXC Windshield Kit (1436-501)  NOTE: Read these Installation Instructions thoroughly before beginning the installation process. Retain these Installation Instructions for future reference. Kit includes: p/n QTY 2441-243 2441-242 2441-244 2441-241 2441-247 2441-245 2441-246 * * * * * * * * * * 0453-731 1 1 2 4 1 1 1 2 2 2 2 2 4 4 2 4 4 1 2.
PAGE 2
4. If you plan to proceed with the installation of the Roof Kit (p/n 1436-500) or it will be mounted on your vehicle at this time, apply Self-Adhesive Foam (A) on top of the windshield. If not, keep it for future installation. 7. Fasten the lower part of the windshield assembly onto the front vertical tubes of the ROPS using two C-clamps (A), two machine screws (M6-1.0 X 20 mm) (C), and two fender washers (B) (finger tighten at this time). See Fig. 7. Fig. 7 Fig. 4 UTV-165A 8.
PAGE 3
 NOTE: When installing the gas spring, be sure that the body of the gas spring is secured on the top. 10. Secure the two machine screws (installed in step 2) (A) retaining the grab catch support to the windshield frame. See Fig. 10. 14. Fasten the upper part of the windshield onto the roof using five machine screws (M6-1.0 X 25 mm) (C), five lock washers (B), and five flat washers (A) included in the Roof Kit (p/n 1436-500). See Fig. 12. Fig. 12 Fig. 10 UTV-154A UTV-166A 11.