Parts Catalogue

ManualsBrandsToro ManualsUtility VehicleToro 132-3157

 NOTE: Read these installation instructions thoroughly before beginning the installation process. Retain

these Installation Instructions for future reference.

Arctic Cat

Prowler

Installation Instructions - Accessory Kit

Form No. 0453-473

Prowler H1 Oil Cooler Kit

(p/n 1436-481)

Application: 550-700 H1 models without oil cooler

p/n QTY DESCRIPTION

0513-023 2 Mounting Bracket (Non-power steering)

0513-041 1 Mounting Bracket (HDX Power steering)

0513-040 1 Mounting Bracket (XT, XTX Power Steering)

0423-577 1 U-Nut Clip

8476-616 1 Machine Screw

8408-816 2 Cap Screw (M8 x 1.25 x 16) *

8409-020 2 Cap Screw (M10 x 1.25 x 20) *

8424-002 2 Nyloc Nut (M10 x 1.25) *

0413-211 1 Oil Cooler

8409-025 2 Cap Screw (10 mm)

8428-002 2 Flange Lock Nut

0410-166 1 Oil Cooler Hose (Left Side)

0623-028 4 Clamp

0410-165 1 Oil Cooler Hose (Right Side)

0830-166 1 O-Ring

0123-903 6 Cable Tie

0812-055 1 Tower

0812-056 1 Union

0812-034 1 Oil Filter

0623-784 1 Self-Tapping Screw

0453-473 1 Instructions

 NOTE: Refer to your local Arctic Cat ROV dealer

or the appropriate ROV Service Manual for more

detailed instructions.

 NOTE: These instructions are divided into three

sections. (A) Prowler HDX with power steering

(page 1), (B) Prowler XT and XTX with power steer-

ing (page 2) and all (C) non-power steering Prowler

XT and XTX models (page 4).

(A) Prowler HDX Installation

1. Remove seat, seat base and center floor section.

2. Loosen all screws securing the dash; then move

the dash to gain access to all screws securing the

front storage box. Remove the storage box.

3. Secure Mounting Bracket (p/n 0513-041) to the

steering rack frame using two Cap Screws (M8

x 1.25 x 16). Tighten to 20 ft-lb. See Fig. 1.

Fig. 1

ROV-145A

4. Secure the top of the oil cooler to the back side

of the frame and secured using Self-Tapping

Screw; then secure the lower tabs to the back

side of the mounting bracket using two Cap

Screws (M10 x 1.25 x 20) and two Flange Lock

Nuts. Tighten to 20 ft-lb. See Fig. 2.

Fig. 2

ROV-146A

5. Secure Right-Side Oil Cooler onto the passenger

side oil cooler fitting with a Clamp. Tighten to

20 in.-lb.

6. Secure Left-Side Oil Cooler Hose onto the oper-

ator side oil cooler fitting with a clamp. Tighten

to 20 in.-lb. See Fig. 3.

Summary of content (5 pages)

PAGE 1
Form No. 0453-473 Arctic Cat® Prowler Installation Instructions - Accessory Kit Prowler H1 Oil Cooler Kit (p/n 1436-481)  NOTE: Read these installation instructions thoroughly before beginning the installation process. Retain these Installation Instructions for future reference. Fig.
PAGE 2
Fig. 3 15. Place the left-side oil cooler hose onto the leftside tower fitting (as viewed from the rear of the vehicle). Be sure to push the hose completely onto the fitting: then secure with a clamp and tighten to 20 in.-lb. 16. Place the remaining oil cooler hose onto the opposite cooler fitting and secure with clamp as described above. 17. Secure both oil cooler hoses to the frame tubes using cable ties as needed. See Fig. 5. Fig.
PAGE 3
Fig. 9 4. Place U-Nut Clip over the tab located on the top of the oil cooler making sure the clip is positioned with the threaded section facing the rear of the vehicle. 5. Position Oil Cooler making sure the oil cooler tab is positioned on the back side of the mounting tab and that the oil cooler fittings are facing toward the rear of the vehicle; then using Machine Screw, secure the upper tab of the oil cooler to the crossover support bracket. Loosely secure at this time. See Fig. 7. Fig.
PAGE 4
Fig. 12 18. Place the left-side oil cooler hose onto the leftside tower fitting (as viewed from the rear of the vehicle). Be sure to push the hose completely onto the fitting: then secure with a clamp and tighten to 20 in.-lb. 19. Place the remaining oil cooler hose onto the opposite cooler fitting and secure with clamp as described above. 20. Secure both oil cooler hoses to the frame tubes using cable ties as needed. See Fig. 11. Fig.
PAGE 5
9. From the front of the vehicle, insert the two Cap Screws (M10 x 1.25 x 20) (E) through the two lower oil cooler tabs (positioned in front of the mounting tabs) and through the newly installed brackets on the rack and pinion. Loosely secure with Flange Lock Nuts. 10. Tighten the two cap screws and nuts securing the rack and pinion to the frame to 50 ft-lb. 20. Place the tower onto the engine with the O-ring contacting the engine case. 21.