Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSecurity Cage Kit, Groundsmaster 5900 Traction Unit with 2 Post ROPS Extension

FormNo.3407-307RevB

SecurityCageKit

Groundsmaster

5900TractionUnitwith2PostROPSExtension

ModelNo.132-3695

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Thiskitts2PostROPSExtensionKitModel31353only.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,shutoffthe

engine,removethekeyfromtheignitionswitch,

andengagetheparkingbrake.

2.IftherearelightsontheROPSposts,remove

thelightsandmountinghardwarefromthe

ROPSposts.

Note:Retainthelightsandmountinghardware.

3.Ifa2postROPSExtensionwasinstalledon

theunit,removethesidepanelsthatareused

tomounttheROPSpostlights.

Note:RetaintheROPSclampsand

correspondinghardware.

4.Positionthecontrolconsoletothefurthest

inwardposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-307*B

Summary of content (8 pages)

PAGE 1
Form No. 3407-307 Rev B Security Cage Kit Groundsmaster® 5900 Traction Unit with 2 Post ROPS Extension Model No. 132-3695 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. This kit fits 2 Post ROPS Extension Kit Model 31353 only. 1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface, shut off the engine, remove the key from the ignition switch, and engage the parking brake. 2.
PAGE 2
Procedure 2 Note: Refer to Figure 1 as you perform the following steps. Assembling the Kit 1. Remove the toolbox from the machine to allow you to perform step 2. 2. Install the left and right, rear panels onto the back of the platform assembly with 4 bolts (5/16 x 3/4 inch) and 4 nuts. 3. Install the left and right transition panels to the sides of the platform assembly with 6 bolts (5/16 x 3/4 inch) and 6 nuts. 4.
PAGE 3
rear panel. Adjust the position of the screen assembly if necessary. 15. Secure the left and right door-mount assemblies to the corresponding side of the machine. Note: Place the hinge assembly connected to each door onto the previously installed door-mount assemblies with 4 spacers. 16. Install a spring mount to each side of the upper bracket with 8 bolts (5/16 x 3/4 inch) and 8 nuts (5/16 inch). 17.
PAGE 4
g036111 Figure 1 10. Latch pin 19. Right rear panel 28. Window-hinge assembly 2. Left side panel 11. Pin guard 20. Center rear panel 29. Nut (#10) 3. Right side panel 12. Thrust washer 21. Rubber bushing (0.31 inch 30. Shoulder bolt (5/16 x 1-1/4 long) inches) 4. Mount bracket 13. Jam nut 22. Catch latch 31. Screen-backer plate 5. Left transition panel 14. Spacer 23. Rear screen assembly 32. Left hinge 6. Right transition panel 15. Left door-mount assembly 24. Rubber latch 33.
PAGE 5
3 4 Assembling the Door Latch Adjusting the Door-Latch Pins Parts needed for this procedure: 2 Jam nut 2 Pin guard 2 Latch-pin cam 4 Thrust washer 2 Latch pin No Parts Required Procedure 1. Center the latch pin in the latch-pin-mount bracket on the rail (Figure 3). Procedure 1. Ensure that you adjusted the control console to the furthest inward position. 2. Align the latch-pin cam with the opening at the striker plate in the position shown in Figure 2.
PAGE 6
Procedure Note: If the height measured is more than the zone specification, rotate the latch-pin cam 45° toward the inside of the cab to achieve the specified measurement. If the height measured is less than the zone specification, perform the opposite of the above procedure. Note: Refer to Figure 5 as you perform the following steps. Note: The latch pin self centers. g036321 Figure 4 1. Bubble seal 3. 1.9 to 2.2 cm (3/4 to 7/8 inch) 2. Cab rail 4. Tighten the jam nut once the latch pin reaches 1.
PAGE 7
g036172 Figure 5 1. Dual-tab mount 5. Lower windshield assembly 9. Rubber bushing (0.31 inch long) 2. Side-tab mount 6. Upper windshield assembly 10. Rubber bushing (0.56 inch long) 3. Top-tab mount 7. Bolt (5/16 x 1-1/2 inches) 11. Nut (5/16 inch) 4. Rivet 8. Backup washer 6 Completing the Installation No Parts Required Procedure Install any attachments that you previously removed, such as lights, onto the left and right panels.
PAGE 8