Form No. 3407-314 Rev B 安全ケージキット Groundsmaster® 5900 ト ラ ク シ ョ ン ユ ニ ッ ト 2 柱 式 ROPS エ ク ス テ ン ション搭載機用 モ デ ル 番 号 132-3695 取り付け要領 注 前後左右は運転位置からみた方向です。 このキットは、2 柱式 ROPS エクステンションキットモデル 31353専用です。 1 マシンの準備を行う 必要なパーツはありません。 手順 1. 平らな場所に駐車し、エンジンを停止させ、駐車 ブレーキを掛けてキーを抜き取る。 2. ROPSにランプが取り付けられている場合には、 ランプとその取り付け具を外す。 注 外したランプなどは後で取り付けます。 3. 2 柱式 ROPS エクステンションがすでに取り付け 済みの場合は、ROPS にランプを取り付けるた めのサイドパネルを取り外す。 注 ROPS のクランプなど外した部品は後で取 り付けます。 4.
手順 2 注 以下の作業については、図 1を参照のこと。 キットを組み立てる 1. ステップ2の作業ができるように、機体から工具 箱を外す。 2. 左右の後パネルを、プラットフォームアセンブリの 背面に取り付けるボルト5/16 x 3/4 インチ4本と ナット個を使用する。 3. 左右のトランジッションパネルを、プラットフォーム アセンブリの左右各側に取り付けるボルト5/16 x 3/4 インチ6本とナット6個を使用する。 4. キャッチ用ラッチを中央後パネルに取り付けるボル ト10-24 x 5/8 インチ4本とナット4個を使用する。 5. 左右の後パネルに中央の後パネルを取り付けるボ ルト5/16 x 3/4 インチ4本とナット4個を使用する。 6. 先ほど外した工具箱を取り付ける。 7.
15. 左右のドア取り付けアセンブリを、機体のそれぞ れの側に取り付ける。 注 各ドアについているヒンジアセンブリを、先ほ ど取り付けたドア取り付けアセンブリに、スペー サ4個とともに取り付ける。 16. 左右の上側ブラケットにスプリングマウントを取り 付けるボルト5/16 x 3/4 インチ8本、ナット5/16 イ ンチ8個を使用する。 17.
g036111 図1 1. 左後パネル 10. ラッチピン 19. 右後パネル 2. 左サイドパネル 中央後パネル 右サイドパネル ピンガード スラストワッシャ 20. 3. 11. 12. 4. 取り付けブラケット 13. ジャムナット 28. 29. 窓用ヒンジアセンブリ ナット #10 ゴム製ブッシュ長さ 0.31 イ 30. ショルダボルト5/16 x 1-1/4 インチ ンチ 22. キャッチのラッチ 31. スクリーンバッカーブレート 21. 5. 左側トランジッションパネル 14. スペーサ 23. 後スクリーンアセンブリ 32. 6. 右側トランジッションパネル 15. 左ドアマウントアセンブリ 24. ゴム製のラッチ 7. 8. ボルト5/16 x ¾" ナット 5/16" 16. 右ドアマウントアセンブリ 25. スプリングマウント 33. 右側ヒンジ 34. Bolt (#10 x 5/8 inch) 17. 左ドアケージアセンブリ 26. ボールスタッド 35. 9.
3 4 ドアラッチを組み付ける ドアのラッチピンを調整する この作業に必要なパーツ 必要なパーツはありません。 2 ジャムナット 2 ピンガード 2 ラッチピンのカム 4 スラストワッシャ 2 ラッチピン 手順 1. ラッチピンを、レール上のラッチピン取り付けブラ ケットの中央に合わせる (図 3)。 手順 1. コントロールコンソールが一番内側の位置にに セットされていることを確認する。 2. 図 2に示すように、ラッチピンのカムをストライカ プレートの開口部に合わせて取り付ける。 g036952 図3 g026501 2. 図2 1. ジャムナット 4. スラストワッシャ 2. ストライカブレート 5. ラッチピン 3. ラッチピンのカム 6. ピンガード 3. 注 ラッチピンがドアラッチに完全に嵌らない場合 は、ラッチピンのカムとラッチピンとの間にスラス トワッシャを 1-2 枚入れる。 3.
手順 注 高さが所定範囲を超えている場合には、ラッ チピンのカムを45° キャブの内側に向けて回転さ せて高さを範囲内に収めてください。高さが所定 範囲未満の場合には、逆方向に回転させて修正 してください。 注 以下の作業については、図 5を参照のこと。 注 ラッチピンはひとりでに中央に収まります。 g036321 図4 1. バブルシール 2. キャブのレール 3. 1.9-2.2 cm ラッチピンが 1.9-2.2 cm に収まったら、図 3のよ うにジャムナットを締め付ける。 4. 5 ウインドシールドを取り付ける この作業に必要なパーツ 1 デュアルタブマウント 2 サイドタブマウント 1 トップタブマウント 6 リベット 1 下部ウインドシールドアセンブリ 1 上部ウインドシールドアセンブリ 13 ボルト 5/16 x 1½ インチ 13 バックアップワッシャ 13 ゴム製ブッシュ長さ 0.31" 13 ゴム製ブッシュ長さ 0.56" 13 ナット 5/16 インチ 6 1.
g036172 図5 1. デュアルタブマウント 5. 下部ウインドシールドアセンブリ 9. ゴム製ブッシュ長さ 0.31 インチ 2. 3. 4. サイドタブマウント 6. 上部ウインドシールドアセンブリ トップタブマウント リベット 7. ボルト5/16 x 1½ インチ 10. 11. ゴム製ブッシュ長さ 0.56 インチ ナット5/16 インチ 8.