Installation Instructions

ManualsBrandsToro ManualsRiding ProductsManual Spray Kit, 2015 and After Multi Pro 5800 Turf Sprayer

Table Of Contents

.
- ? Installing the Valve Module
- ? Installing the Speedometer

FormNo.3396-307RevA

ManualSprayKit

2015andAfterMulti-Pro5800TurfSprayer

ModelNo.132-5570

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Valvemodule1

Bolt(1/4x5/8inch)

Washer(1/4inch)

Nut(1/4inch)

Installthevalvemodule.

Speedometer

Wiringharness1

Fuse(10amp)

Installthespeedometer.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Note:YoumayneedaFuseBlockKit(Toropartnumber

92-2641)toprovidepowertothespeedometerifthereareno

openfuseports.ContactyourToroDistributortopurchase

thiskit.

InstallingtheValveModule

1.Positionthemachineonalevelsurface,settheparking

brake,turntheignitionoff,andremovethekey.

CAUTION

Ifyouleavethekeyintheignitionswitch,

someonecouldaccidentlystarttheengineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheignitionswitch

beforeyoudoanymaintenance.

2.Disconnectthenegativebatteryterminalfromthe

battery;refertoyourOperator’sManual.

3.Openthehood.

4.Installthevalvemoduletothefrontofthestorage

compartmentusing2bolts,2washers,and2nuts

(Figure1).

Figure1

1.Valvemodule3.Washer

2.Nut4.Bolt

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3396-307*A

Summary of content (4 pages)

PAGE 1
Form No. 3396-307 Rev A Manual Spray Kit 2015 and After Multi-Pro 5800 Turf Sprayer Model No. 132-5570 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. Valve module Bolt (1/4 x 5/8 inch) Washer (1/4 inch) Nut (1/4 inch) Speedometer Wiring harness Fuse (10 amp) 1 2 2 2 1 1 1 Install the valve module. Install the speedometer.
PAGE 2
Installing the Speedometer 5. Connect the speedometer wire harness to the wheel-motor connector using the 3-pin weather-pack connector end (Figure 4). 1. Remove the knock out in the dash of the machine and install the speedometer in its place Figure 2. Note: This connection is near the rear, right fender of the vehicle. 1 1 2 G017084 G017083 Figure 4 Figure 2 1. Weather-pack connector 2. Wheel-motor connector 1. Knock out 6. Secure the wiring harness to the frame. 2.
PAGE 3
9. If no power terminals on the existing fuse block are available, install an additional fuse block (Toro part number 92-2641) and the 10-amp fuse (Figure 6). 2 1 G017086 Figure 6 1. Fuse block 2. Fuse (10 amp) 10. Plug in an available power terminal from the fuse block. 11. Connect the black wire with a ring terminal to the ground-terminal block (Figure 7). 1 G017087 Figure 7 1. Ring terminal on the terminal block 12. If not done already, install the 10-amp fuse to the fuse block. 13.
PAGE 4