Form No. 3397-674 Rev A Console Kit Greensmaster® 3300 or 3400 Series TriFlex® Traction Unit Model No. 132-9542 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 132-9548 1. Engine speed (high) 7. Traction unit (neutral) 2. Engine speed (low) 8. Reel (transport) 3. Lower and engage the reels 9. Reel (mow) 4.
132-9549 1. Read the Operator's Manual before servicing or performing maintenance. 2. Hydraulic fluid level 4. Engine (start) 5. Engine (run) 3. Choke 6. Engine (stop) Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the console.
Preparing the Machine Disconnect the Wire Harness Disconnect the wire harness from the controls, switches, and indicators mounted on the console assembly (Figure 2). 1. Move the machine to a level workspace. 2. Shut off the engine, set the parking brake, and remove the key from the ignition switch. 3. Disconnect the battery; Refer to the Operator’s Manual. Removing the Console Removing the Console Cover Note: Set aside all of the items that you remove from this procedure.
Removing the Throttle Assembly 2. Remove and set aside the dust boot from the mow-control shaft (Figure 4). 3. Remove and set aside the 2 bolts and nuts securing mow-control assembly to the console assembly (Figure 4). 1. Remove and set aside the knob from the throttle-lever shaft. 2. Remove and discard the 2 bolts and locknuts that secure the throttle assembly to the console assembly (Figure 3).
. Remove the nuts securing the proximity sensors to the function-lever bracket (Figure 7). Figure 7 1. Retaining nut Figure 9 3. Proximity sensor 1. Bolt 2. Function-control assembly 2. Washer 3. Nut 6. Remove the knob from the function lever (Figure 8). Disconnecting the Choke Cable 1. Disconnect the cable from the choke control on the engine. 2. Remove the cable from the traction unit. 3. Leave the cable connected to console assembly, it will be removed with the console assembly.
Removing the Switches and Indicators Note: Set aside all of the items that you remove from this procedure. 1. Remove the warning indicators from the console assembly, if equipped (Figure 10). Figure 12 Cutaway View 1. Hour meter 3. Cutaway view 2. Retainer 4. Remove the retaining nut on the ignition switch to remove it from the console assembly (Figure 13). Figure 10 1. Warning (oil and battery) 3. Service required 2. Warning (glow plug and temperature) 4. Hole plug 2.
Removing the Console Assembly 2. Use the 2 carriage bolts and flange nuts that you removed earlier to secure the console bracket (Figure 16). Set aside all of the items that you remove from this procedure. 1. Remove the 2 carriage bolts and flange nuts that secure the console assembly to the console bracket (Figure 14). Note: Install the spacer on machines that are diesel powered. Figure 14 1. Console assembly 3. Arm rest 2. Flange nut 4.
2. Install the dust boot over the joystick shaft. 3. Install the knob to the joystick shaft. Installing the Choke Assembly Gas Engine Only 1. Follow the original cable routing to route the new choke cable and secure it to the machine with cable ties (Figure 18). Figure 19 1. Speed nut 3. Choke-lever assembly 2. Bolts (#10 x 1/2 inch) 5. Connect the cable to the choke control on the engine.
Installing the Function-Control Assembly 1. Use the bolt (#10 x 1/2 inch) and locknut to secure the function-lever bracket to the console (Figure 21). Figure 23 1. Nut 2. Lock washer 3. Function-lever bracket 4. Proximity sensor 4. Install the knob to the function-lever shaft. Installing the Neutral-Lock Cable Figure 21 1. Bolt (#10 x 1/2 inch) 1. Remove the original cable and route the new cable in its place. 3. Function-lever bracket 2. Locknut 2.
Figure 27 Figure 25 1. Bolt (1/4 x 5/8 inch) 4. Cable 2. Cable clamp 5. Cable connector 1. Audio alarm 2. Retaining ring 3. Use the retaining nut you removed earlier to secure the ignition switch to the console assembly (Figure 28). 3. Retainer nut 4. Install the retainer nut on to the console assembly (Figure 25). 5. Use the 2 bolts (1/4 x 5/8 inch) to secure the cable with the cable clamp to the console assembly (Figure 25). 6. Secure the cable to the machine with cable ties.
Figure 29 Gasoline Engine 1. Warning (oil and battery) 3. Warning (hydraulic) 2. Service required 4. Hole plug Figure 31 1. Control, indicator, or switch 2. Connector Completing the Install 1. Use the 8 bolts that you removed earlier to secure the console cover to the console assembly (Figure 32). Figure 30 Diesel Engine 1. Warning (oil and battery) 3. Hole plug 2. Service required 4. Warning (glow plug and temperature) Figure 32 5.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
