Installation Instructions

ManualsBrandsToro ManualsAttachmentsLED Worklight Kit, Workman MD or HD Series Utility Vehicle

FormNo.3404-236RevA

LEDWorkLightKit

Workman

MDorHDSeriesUtilityVehicle

ModelNo.133-0554

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

107-8008

1.Worklight—rear

2.Worklights—front

107-8011

1.Work-lightfuse—15A

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3404-236*A

Summary of content (8 pages)

PAGE 1
Form No. 3404-236 Rev A LED Work Light Kit Workman® MD or HD Series Utility Vehicle Model No. 133-0554 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
PAGE 3
For MD Utility Vehicles Route the wire harness as shown in Figure 1 and secure the wire harness to the machine with cable ties as necessary.
PAGE 4
For HD Utility Vehicles Route the wire harness as shown in Figure 2 and secure the wire harness to the machine with cable ties as necessary.
PAGE 5
3 Installing the LED Work Lights Parts needed for this procedure: 3 LED work light 2 Light channel 1 Work-light bracket 6 Spring washer 4 Hex-head bolt (5/16 x 3/4 inch) 4 Locknut (5/16 inch) 4 Light-channel-mount bracket 4 Hex-head bolt (1/4 x 2-3/4 inches) 4 Flat washer (1/4 inch) 4 Flange nut (1/4 inch) Figure 4 1. Flange nut (1/4 inch) 3. Flat washer (1/4 inch) 2. Light-channel-mount bracket 4. Hex-head bolt (1/4 x 2-3/4 inches) 3.
PAGE 6
Figure 7 1. Plastic plug 2. Insert the rocker switch into the opening and apply the work-light decal to the left of the rocker switch (Figure 8). Figure 6 1. Opening in the LED work light 2. Wire-harness connector 4 Installing the Rocker Switch Figure 8 1. Work-light decal Parts needed for this procedure: 1 Rocker switch 1 Work-light decal 2. Rocker switch 3. Connect the female connector attached to the wire harness to the rocker-switch blades (Figure 9). Procedure 1.
PAGE 7
2. Connect the wire-harness-terminal ring to the ground-block terminal (Figure 12 or Figure 13). 5 Connecting the Wire Harness to the Ground-Block Terminal and Installing the Fuse Parts needed for this procedure: 1 Fuse (15 A) 1 Fuse decal Figure 12 MD Model Shown Procedure 1. Insert the fuse (15 A) into the fuse block and apply the fuse decal beneath the fuse block (Figure 10 or Figure 11). 1. Ground-block terminal Figure 13 HD Model Shown Figure 10 MD Model Shown 1. Fuse decal 2. Fuse (15 A) 1.
PAGE 8
6 Connecting the Battery No Parts Required Procedure Connect the negative battery cable; refer to your Operator’s Manual. 7 Testing the LED Work Lights No Parts Required Procedure Push the rocker switch up to turn the front LED work lights to the ON position. Push the rocker switch down to turn the rear LED work lights to the ON position. Push the rocker switch to the middle position to turn the LED work lights to the OFF position.