Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 133-1434

FormNo.3403-305RevB

ChuteGateKit

GrandStand

Mower

ModelNo.133-1434

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

117-8569

1.Operatordischargecontrol3.Closed

2.Open4.ReadtheOperator's

Manual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3403-305*B

Summary of content (8 pages)

PAGE 1
Form No. 3403-305 Rev B Chute Gate Kit GrandStand® Mower Model No. 133-1434 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. Remove the existing side-discharge chute. No parts required – Side-discharge chute Bolt (5/16 x 7-1/2 inch) Locknut (5/16 inch) Spacer Spring Handle assembly Bolt (3/8 x 1 inch) Nut (3/8 inch) 1 1 1 1 1 1 2 2 Cable tie 3 Route the cables. Trash bag 1 Install the trash bag. Install the side-discharge chute. Install the handle.
PAGE 3
. Tighten the nut until the end of the bolt is flush with the end of the nut. 2 Note: Do not overtighten. Important: The grass deflector must be able to lower down into position. Lift the deflector up to test that it lowers into the full down position.
PAGE 4
3. Install the handle assembly to the machine using 2 bolts and 2 nuts as shown in Figure 4. 4 Routing the Cables Parts needed for this procedure: 3 Cable tie Procedure 1. Route the cables across the machine, in front of the fuel tank (Figure 5). Figure 4 1. Handle assembly 3. Nut 2. Bolt 4. Install the fuel tank and secure the cushion; refer to the Operator’s Manual for the machine. Figure 5 Engine not shown 1. Fuel tank 2. Cable 2.
PAGE 5
3. Remove the nuts from the cables. 4. Thread the cables through the rear discharge-chute bracket (Figure 7). Note: Route the cable that is on the left side of the handle assembly through the left side of the bracket; route the other cable through the right side. Figure 9 Engine not shown in callout bubble Figure 7 1. Discharge-chute brackets 2. Pulley 1. Cable tie 5. Install 1 nut on each cable. 5 6. Thread the cables through the front bracket and install the other nuts onto the cable (Figure 8).
PAGE 6
Operation Using the Chute Gate CAUTION The chute gate does not seal the discharge opening. Grass and objects may be thrown toward bystanders, resulting in serious injury. • Be aware of the mower discharge direction and do not point it at anyone. • Remove obstacles such as rocks, tree limbs, etc. from the mowing area. • Never put your hands or feet under the mower or discharge area. • Never try to clear the discharge area or mower blades unless the engine is off and you remove the key.
PAGE 7
Notes: 7
PAGE 8