Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 133-1436

FormNo.3403-313RevC

RollerStriperKit

GrandStand

Mower

ModelNo.133-1436

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Note:Ifyouhaveabaggerattachedtoyourmachine,thiskitwillnott.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Drilltheholesintotheplatformgussets.

Leftstriper-mountbracket

Rightstriper-mountbracket1

Flatwasher4

Hex-headbolt(3/8x4inches)

Installthestriper-mountbrackets.

Rollerassembly1

Lefttorsionspring

Righttorsionspring1

Pivotrod1

Pivottube1

Pivotwasher2

Hairpincotter2

Installtherollerassembly.

Nopartsrequired

–

Connectthechains.

Nopartsrequired

–

Installthewheels.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3403-313*C

Summary of content (12 pages)

PAGE 1
Form No. 3403-313 Rev C Roller Striper Kit GrandStand® Mower Model No. 133-1436 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: Determine the left and right sides of the machine from the normal operating position. Note: If you have a bagger attached to your machine, this kit will not fit.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Disengage the PTO. 2. Move the motion-control levers to the NEUTRAL-LOCK position. 3. Move the throttle control to the SLOW position. 4. Engage the parking brake. 5. Shut off the engine and remove the key.
PAGE 3
2 Drilling the Holes into the Platform Gussets No Parts Required Procedure Using the measurements shown in Figure 2, drill a 9.5 mm (3/8 inch) hole into each side of the platform gussets. Note: Only drill holes into the platform gussets, if necessary. Some models already have the holes. g207688 Figure 2 1. 16 mm (5/8 inch) 2.
PAGE 4
6. 3 Installing the Striper-Mount Brackets Loosely install a striper-mount bracket to the transmission mount using 2 hex-head bolts (3/8 x 4 inches), previously removed 2 flange nuts (3/8 inch), and 2 flat washers on each side (Figure 4). Parts needed for this procedure: 1 Left striper-mount bracket 1 Right striper-mount bracket 4 Flat washer 4 Hex-head bolt (3/8 x 4 inches) Procedure 1. Jack up the rear of the machine. 2. Use jack stands to support the rear of the machine. 3.
PAGE 5
4 Installing the Roller Assembly Parts needed for this procedure: 1 Roller assembly 1 Left torsion spring 1 Right torsion spring 1 Pivot rod 1 Pivot tube 2 Pivot washer 2 Hairpin cotter Procedure 1. Position the springs into the striper-mount brackets (Figure 5). Ensure that the short, outside fingers on the springs are under the striper-mount brackets (Figure 5). 2.
PAGE 6
g223750 Figure 5 1. Left spring long finger 4. Right spring short finger 7. Hairpin cotter 2. Pivot tube 5. Pivot rod 8. Roller assembly 3. Right spring long finger 6. Pivot washer 9. Nuts on top of the roller assembly 4. Tighten the fasteners on the striper-mount brackets and roller assembly (Figure 4 and Figure 5). 5. Pull the inside spring finger up over the roller mount (Figure 6). g214431 Figure 6 1. Left spring long finger 3. Right spring short finger 2.
PAGE 7
5 Connecting the Chains No Parts Required Procedure 1. Hold the operator platform while releasing the platform latch. 2. Lower the platform down completely. 3. With the platform down, raise the roller up, and rotate the lift handle over the platform (Figure 7). g010976 Figure 8 1. Hole in the lower, front side plate of the platform 5. 2. Snap ring Repeat this procedure on the other side. 6 Installing the Wheels No Parts Required Procedure g223751 Figure 7 1. Platform down 2. Lift handle 4.
PAGE 8
Operation Operating Tips Raising the Roller Striping Quality Is Influenced by Grass Condition and Type With the platform down, raise the roller up, and rotate the lift handle over the platform (Figure 9). • Limp grass where wheel tracks are very visible is usually good for striping. • Stiff grass where wheel tracks are less visible usually produces poor striping. • Cool-season grass types found in northern areas are usually good for striping.
PAGE 9
Visibility of Striping Depends on the Condition of the Lawn Some Lawns Must Be Trained to Show a Striping Contrast • Avoid operating in wet conditions on slopes, if • On a new property during the first 2 weeks, you possible. • Large, flat areas usually provide better striping contrast than on slopes or areas with a lot of trimming and edging. • • Mowing in morning dew can produce good striping • contrast.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12