Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 133-1438

FormNo.3437-535RevA

ElectricalAccessoryPort

GrandStand

MowerorProLineCommercialWalk-BehindMower

ModelNo.133-1438

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Note:Ifyourmachinehasmultipleelectricalaccessoriesinstalled,youneedaYadapter(ToroPartNo.

121-5988,soldseparately)toinstallthiskit.

InstallingtheKittoa

GrandstandMower

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

4.Removethenegative(-)batterycablefromthe

battery.

Installingthe12VReceptacle

1.Releasethecushion.

2.Removetheknockoutontherightsideofthe

machine(Figure1).

g035546

Figure1

1.Knockoutlocation2.12Vreceptacle

3.Removethelockingringfromthe12V

receptacle.

4.Installthe12Vreceptacleandsecureitwiththe

lockingring(Figure1).

ConnectingthePortWireHarness

1.Installthepostconnectorsfromtheportwire

harnesstothepostsonthe12Vreceptacle

(Figure2).

g311406

Figure2

1.Negative(-)connector3.Positive(+)connector

2.Negative(-)post4.Positive(+)post

2.Connectthewireharnessasfollows.

•Machineswithoutanyelectric

accessories—connecttheportwire

harnesstothemachinewireharness(Figure

3).

g035549

Figure3

1.Machinewireharness2.Portwireharness

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3437-535*A

Summary of content (4 pages)

PAGE 1
Form No. 3437-535 Rev A Electrical Accessory Port GrandStand® Mower or ProLine Commercial Walk-Behind Mower Model No. 133-1438 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Note: If your machine has multiple electrical accessories installed, you need a Y adapter (Toro Part No. 121-5988, sold separately) to install this kit. Installing the Kit to a Grandstand Mower Connecting the Port Wire Harness 1. Preparing the Machine 1.
PAGE 2
• Machines with either a light kit or other electric accessory—connect the port wire harness to the light kit or other accessory wire harness. • Machines with both a light kit and other electric accessory—complete as follows: Note: You need a Y adapter (Toro Part No. 121-5988, sold separately) to connect the port wire harness with both accessories installed on the machine. A. Disconnect the other accessory from the light kit harness. B.
PAGE 3
Installing the Kit to a ProLine Mower Connecting the Port Wire Harness 1. Install the post connectors from the wire harness to the posts on the 12 V receptacle. Preparing the Machine 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. 4. Remove the negative (-) battery cable from the battery. Installing the 12 V Receptacle 1. g311406 Figure 6 Remove the knockout on the right side of the machine (Figure 5). 1.
PAGE 4
• Machines with 2 other electric accessories—complete as follows: Note: You need a Y adapter (Toro Part No. 121-5988, sold separately) to connect the port wire harness with both accessories installed on the machine. A. Disconnect the second accessory from the accessory connected to the machine wire harness. B. Connect the 1-connection end of the Y adapter to the connected accessory wire harness (Figure 8).