Installation Instructions

ManualsBrandsToro ManualsRiding ProductsWheel Motor Kit, Reelmaster 5410, 5510, 5610 or Groundsmaster 4300-D Traction Unit

FormNo.3403-434RevA

WheelMotorKit

Reelmaster

5410,5510,5610orGroundsmaster

4300-DTraction

Unit

ModelNo.133-2950

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Important:Theseinstructionscovertheremoval

andinstallationofnewwheelmotors,wheel-motor

components,andhydrauliclters.Iftheoriginal

traction-circuitcomponentshavebeendamaged,

additionalrepairsandhigh-pressurehydraulic-system

ushingmustbeperformedpriortoinstallingnewwheel

motors.Contactyourlocaldistributorforadditional

information.

WARNING

Hydraulicuidescapingunderpressurecanhave

sufcientforcetopenetratetheskinandcause

seriousinjury.Ifuidisinjectedintotheskin,it

mustbesurgicallyremovedwithinafewhoursby

adoctorfamiliarwiththistypeofinjury.Gangrene

mayresultfromsuchaninjury.

Beforedisconnectingorperforminganyworkon

thehydraulicsystem,relieveallpressureinthe

system.Shutofftheengine;lowerorsupportall

cuttingunits.

Keepyourbodyandhandsawayfrompinholeleaks

ornozzlesthatejecthydraulicuidunderhigh

pressure.Usepaperorcardboard,nothands,to

searchforleaks.

CAUTION

Ifthemachineisnotproperlysupported,the

machinemaymoveorfall,whichmayresultin

personalinjury.

Whenchangingattachmentsortiresorperforming

otherservice,usecorrectblocks,hoists,andjacks.

Makesurethatthemachineisparkedonasolid,

levelsurfacesuchasaconcreteoor.Priorto

raisingthemachine,removeanyattachmentsthat

mayinterferewiththesafeandproperraisingofthe

machine.Alwaysensurethatthemachineissecure

frommovementbeforeyoustarttoworkonit.

Usejackstandsorotherappropriateload-holding

devicestosupporttheraisedmachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3403-434*A

Summary of content (4 pages)

PAGE 1
Form No. 3403-434 Rev A Wheel Motor Kit Reelmaster® 5410, 5510, 5610 or Groundsmaster® 4300-D Traction Unit Model No. 133-2950 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Important: These instructions cover the removal and installation of new wheel motors, wheel-motor components, and hydraulic filters.
PAGE 2
Removing the Old Components removal or installation. Hammering may cause damage to the wheel motor. 4. Use an appropriate puller (Toro Part No. TOR6004) to loosen the wheel hub from the wheel motor. 1. Park the machine on a level surface, engage the parking brake, lower the cutting units, and shut off the engine. Remove the key from the ignition switch. 5. Remove the locknut and the wheel hub from the motor shaft (Figure 1). 2. Remove the front wheels from the machine as follows: 6.
PAGE 3
7. Install the square key into the key slot of the wheel-motor shaft. Align the wheel hub with the square key and slide the wheel hub onto the motor shaft. Secure the hub with the locknut. Torque the locknut to 549 to 671 N∙m (405 to 495 ft-lb). 12. Remove the 4 locknuts securing the brake adapter, the wheel motor, and the spring clip to the frame (Figure 1). 13. Remove the brake adapter, the wheel motor, and the brake spring bracket from the machine.
PAGE 4