Installation Instructions

ManualsBrandsToro ManualsWalk-Behind MowersRear Drive Kit, ProStripe 560 Mower

FormNo.3447-369RevB

RearDriveKit

ProStripe

560Mower

ModelNo.134-6408

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Bearingsupportplate2

Bolt(M6x16)

Rearrollerbushing2

Thrustwasher(36mm)

Drivecam4

Drivekey4

Rollerbushing2

Flatwasher6

Spacer

Shaft

Sprocket(22T)

Washer(M6x18)

Bolt(M6x20)

Removetheroller.

Tensionertemplate1

Tensionerpulley1

Capheadbolt(M6x35)

Nut1

Backplate1

Chain

Sprocket(10T)

Thrustwasher(20mm)

Circlip

Finishtheinstallation.

PreparingtheMachine

WARNING

Tippingthemachinemaycausethefuelto

leak.Fuelisammableandexplosive,and

cancausepersonalinjury.

Runtheenginedryorremovethefuelwitha

handpump;neversiphonthefuel.

1.Runtheenginedryorremovethefuelwitha

handpump.

2.Movethemachinetoalevelsurface,shutoff

theengine,waitforallmovingpartstostop,and

allowtheenginetocool.

3.Disconnectthespark-plugwirefromthespark

plug;refertotheOperator’sManualforyour

machine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUK

AllRightsReserved

*3447-369*

Summary of content (8 pages)

PAGE 1
Form No. 3447-369 Rev B Rear Drive Kit ProStripe® 560 Mower Model No. 134-6408 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty.
PAGE 2
Removing the Roller 1. If the grass bag is on the machine, remove the grass bag. 2. Remove the chain cover from the machine by removing the 2 chain-cover bolts (Figure 1). Note: Retain the chain cover and 2 chain-cover bolts for later installation. 3. Remove and discard the existing circlip, thrust washer, sprocket, and chain from the gearbox post (Figure 1). g349697 Figure 1 1. Gearbox post 5. Circlip 2. Chain 3. Sprocket 6. Chain cover 7. Chain-cover bolts (2) 4. Thrust washer 4.
PAGE 3
g357358 Figure 2 1. Bolt (M6 x 16) (3) 8. Flat washer (6) 2. Bearing support plate ( 2) 3. Rear roller bushing (2) 9. Spacer (1) 10. Shaft (1) 4. Thrust washer (36 mm) (2) 11. Sprocket (1) 5. Drive cam (4) 12. Bolt (M6 x 20) (1) 6. Drive key (4) 13. Washer (M6 x 18) (1) 7. Roller bushing (2) Note: Add multiple flat washers to remove sideways movement. 7. Apply thread-locking compound (Loctite 2701 or similar) on the bolt (M6 x 20). Install and torque the bolt to 11 N·m (8 ft-lb).
PAGE 4
Finishing the Installation 1. Line up the tensioner template on the rear axle support and temporarily fix the template in place using a chain cover bolt in the corresponding hole. 2. Drill 4 pilot holes [3 mm (1/8 inch)] in the rear axle support in the locations marked. 3. Remove the template from the machine and discard. 4. Use a 6 mm (1/4 inch) drill bit to open up the 4 holes. Note: The holes will overlap. This is intentional. 5.
PAGE 5
g357359 Parts Ref. Part Number Qty. 1 111-8216 1 2 111-8602 3 Description Ref. Part Number Qty.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8