Installation Instructions

ManualsBrandsToro ManualsAeratorsCE Conversion Kit, 24in Stand-On Aerator

FormNo.3433-517RevF

CEConversionKit

24inStand-OnAerator

ModelNo.135-7423

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal135-3183

135-3183

1.Bypassleverpositionfor

pushingthemachine.

3.Bypassleverpositionfor

operatingthemachine.

2.Readtheinstructions

beforeservicingor

performingmaintenance.

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceandengage

theparkingbrake.

2.Shutofftheengineandremovethekey.

3.Waitforallmovingpartstostop.

4.Allowthemachinetocool.

5.Disconnectthesparkplug;refertothe

Operator’sManualforyourmachine.

RemovingtheCoversand

Guards

NoPartsRequired

Removingthe

Hydraulic-ComponentCovers

1.Remove2thumbscrewsthatsecurethe

hydraulic-componentcovertothemachine,and

removethecover(Figure1).

Note:Discardthecoversandthumbscrews.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3433-517*

Summary of content (8 pages)

PAGE 1
Form No. 3433-517 Rev F CE Conversion Kit 24in Stand-On Aerator Model No. 135-7423 Installation Instructions Safety Installation Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. 1 Preparing the Machine No Parts Required Procedure decal135-3183 135-3183 1. Bypass lever position for pushing the machine. 1.
PAGE 2
g349556 Figure 1 Left side shown 1. Right hydraulic-component cover 2. Thumbscrews 3. Left hydraulic-component cover 4. Cover mount brackets g293458 2. Figure 2 Left side shown Repeat step 1 for the other hydraulic-component cover. Removing the Chain Guards 1. 1. Carriage bolt 4. Chain guard 2. Washer 5. Flange-head screw (1/4 x 1/2 inch) 3.
PAGE 3
Assembling the Chain Guards 3 1. Preparing the Covers and Guards Assemble 2 flange-head capscrew (10 x 35 mm) through the hole into the hydraulic-component cover (Figure 5).
PAGE 4
Assembling the Rear Platform Cover 1. Assemble 2 flange-head capscrews (3/8 x 1 inch) through the holes into the rear platform cover (Figure 6) that you removed in Removing the Rear Platform Cover (page 2). g349606 Figure 7 1. Flange locknut (3/8 inch) g349595 2. Guard mount (sides of the frame) Figure 6 1. Retaining ring (3/8 inch) 3. Flange-head capscrew (3/8 x 1 inch) 2. 2. Rear platform cover 2.
PAGE 5
g349610 Figure 8 1. Right hydraulic-component cover 2. Flange-head capscrew (3/8 x 1 inch) 5. 3. Left hydraulic-component cover g349720 Figure 9 4. Full-threaded bolt (3/8 x 2 inches) 1. Clip nuts (10 mm) Align the slot in the hydraulic-component cover with the full-threaded bolt (3/8 x 2 inches). 6. Assemble the hydraulic-component cover to the machine, and thread the flange-head capscrew and full-threaded bolt into the threaded inserts. 7.
PAGE 6
g349723 g349721 Figure 11 1. Front of the Machine 3. Right side of the machine 2. Left side of the machine Installing the Chain Guards g349722 Figure 10 1. Front of the machine 3. Hydro mount bracket 2. Retaining ring (5/16 inch) 4. Flange-head capscrew (5/16 x 1 inch) 4. 1. Align the flange-head bolts of the CE chain guard with the clip nuts and threaded spacer on the machine (Figure 12). Secure the capscrew to the bracket (Figure 10) with a retaining ring (5/16 inch).
PAGE 7
g349739 Figure 14 1. Mounting flange (frame) 3. Rear platform cover 2. Flange-head capscrew (3/8 x 1 inch) g349736 Figure 13 1. Front of the machine 4. Repeat steps 1 through 3 for the CE chain guard at the other side of the machine. Installing the Rear Platform Cover 1. Align the 2 flange-head capscrews in the rear platform cover with the threaded inserts of the frame mounting flanges (Figure 14). 7 2. Loosely assemble the cover to the flanges with the capscrews. 3.
PAGE 8
5 6 Installing the Decals Finishing Installing the Kit Parts needed for this procedure: No Parts Required 1 Decal 133-5623 (machine manufacturer date) 1 Decal 142-2156 (CE sound) Procedure Connect the spark plug; refer to the Operator’s Manual for your machine. Procedure 1. Install decals 133-5623 (machine manufacturer date) and 142-2156 (CE sound) to the left frame plate as shown in Figure 15. g293414 Figure 15 1. Decal 142-2156 (CE sound) 2. 2.