Installation Instructions

ManualsBrandsToro ManualsSprayersFinishing Kit, Foam Marker for Serial Number 315000001 and After Multi Pro 5800 Turf Sprayer

FormNo.3414-241RevA

FinishingKit

FoamMarkerforSerialNumber315000001andAfterMultiPro

5800TurfSprayer

ModelNo.136-0458

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Foammarker(soldseparately)

Supportbracket

Bolt(5/16x1inch)

Flangedlocknut(5/16inch)

Washer(3/8inch)

Assemblethefoammarker.

Flangedlocknut(5/16inch)

Carriagebolt(5/16x1-1/4inch)

R-clamp1

Bolt(3/8inch)

Nut(3/8inch)

Installthenishingkitbracket.

Wireharness1

Cabletie

Routethewireharness.

Relay1

Flange-headbolt(#10-24x1/2inch)

Fuse(15A)

Connectthewires.

Flange-headbolts(6x12mm)

Mountingbracket(foam-controlswitch)

3-positionpaddleswitch(foam-control

switch)

2-positionrockerswitch(compressor

on/offswitch)

Installtheswitches.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3414-241*A

Summary of content (16 pages)

PAGE 1
Form No. 3414-241 Rev A Finishing Kit Foam Marker for Serial Number 315000001 and After Multi Pro® 5800 Turf Sprayer Model No. 136-0458 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
PAGE 2
Procedure Description Use Qty. 7 Valve mount Hex-slotted screw (1/4–20 x 1/2 inch) Flange-head screw (1/4–20 x 5/8 inch) Flange nut (1/4 inch) 1 2 2 2 Install the valve mount. 8 No parts required – Finish the installation of the kit. Note: The Foam Marker Kit is required to install this product. Contact your Authorized Toro Dealer for more information.
PAGE 3
2 3 Assembling the Foam Marker Installing the Foam Marker and Support Bracket Parts needed for this procedure: Parts needed for this procedure: 1 Foam marker (sold separately) 4 Flanged locknut (5/16 inch) 1 Support bracket 4 Carriage bolt (5/16 x 1-1/4 inch) 4 Bolt (5/16 x 1 inch) 1 R-clamp 4 Flanged locknut (5/16 inch) 1 Bolt (3/8 inch) 4 Washer (3/8 inch) 1 Nut (3/8 inch) Procedure Procedure 1.
PAGE 4
inch) and 2 flanged locknuts (5/16 inch) as shown in Figure 6. 7. If the machine has a rinse kit installed, secure the rinse-kit hose with the R-clamp as shown Figure 7. g029190 g200877 Figure 5 1. Splash guard 4. Right, rear fender 2. Carriage bolt 5. Flanged locknut Figure 7 3. Rear-fender mount 4 3. Align the holes in the front leg of the support bracket with the holes in the fender bracket and fender (Figure 6).
PAGE 5
the wire branch rearward along the sprayer tank as shown in Figure 8 and Figure 9. g029404 Figure 11 g029405 1. Radiator 5. 236 cm (93 inch)—compressor branch 2. Cable tie 6. 240 cm (94-1/2 inch)—dash-panel branch 3. 240 cm (94-1/2 inch)—dash-panel branch (routed down) 7. Wire harness for the machine 4. Air filter (engine) 8. 197 cm (77-1/2 inch)—engine-compartment branch Figure 9 1. Sprayer-tank straps 3. Cable ties 2. 236 cm (93 inch)—compressor branch 2.
PAGE 6
g029403 Figure 12 1. Cable ties 7. Blade connector (wire harness for the finishing kit) 2. 197 cm (77-1/2 8. Front of the machine inch)—engine-compartment branch 3. Base of the center console 9. 240 cm (94-1/2 inch)—dash-panel branch (routed down) 4. Wire harness for the machine 5. Ring terminal (wire harness for the finishing kit) g029402 Figure 13 10. Radiator 11. Air filter 6. 5-socket connect (wire harness for the finishing kit) 1. Cable tie 5. 240 cm (94-1/2 inch)—dash-panel branch 2.
PAGE 7
2. Route the 240 cm (94-1/2 inch)—dash-panel branch of the wire harness to the R-clamp at the ground-speed-control coil (Figure 13 and Figure 14). 3. Route the 240 cm (94-1/2 inch)—dash-panel branch of the wire harness through the grommet at the opening in the forward bulkhead and inboard of the cable and hose hook (Figure 15). g029406 Figure 16 g029401 Figure 15 1. 8-socket connector (compressor switch) 4. 8-socket connector (wire harness for the finishing kit) 2. Cable and hose hook 5.
PAGE 8
5 Connecting the Wires Parts needed for this procedure: 1 Relay 1 Flange-head bolt (#10-24 x 1/2 inch) 1 Fuse (15 A) g200876 Figure 19 Connecting the Compressor Wire 1. Fuse 2. Cable tie 1. At the end of the 236 cm (93 inch) branch of the wire harness, align the 4-socket connector of the wire harness for the finishing kit with the 4-pin connector of the wire harness from the compressor. 3. Ground wire 4. Relay 2. Insert the pins of the relay into the sockets of the connector (Figure 19).
PAGE 9
Connecting the Load Wire Connectors (Optional Auxiliary-Fuse Block) 1. Connect the blade connector of the wire harness for the finishing kit to the socket connector of the auxiliary-fuse block (Figure 22). Note: Press the connectors together until the latch snaps securely. g200871 Figure 20 1. Auxiliary-fuse block 3. Fuse blocks for the machine 2.
PAGE 10
g200872 g029358 Figure 23 1. Auxiliary fuse block 4. 2-socket connector (feed wires of the auxiliary-fuse block) 2. Mounting flange (fuse block for the machine) 5. 2-pin connector (auxiliary-feed wires, fuse block for the machine) Figure 24 1. Threaded inserts (steering column) 3. Flange-head bolts (6 x 12 mm) 2. Mounting bracket (foam-control switch) 3. Fuse block (machine) 2.
PAGE 11
4. Assemble the switch into the bracket and press in the switch until it snaps securely into the opening (Figure 25). Note: Ensure that the paddle for the 3-position paddle switch (foam-control switch) is aligned outward. Installing the Compressor Switch 1. Remove the plug in the dash panel of the machine (Figure 26). g206707 Figure 27 1. 3.8 cm (1.5 inches) 2. 4.1 cm (1.625 inches) 4. Drill hole—1/4 inch diameter 5. Seat base 3. 3.2 cm (1.25 inches) 2.
PAGE 12
Installing the Valve Mount to Model Year 2016 and Later Machines 1. Remove the harness base from the console by loosening and removing the bolts from the harness base (Figure 29). Note: Retain and set aside the bolts. g206715 Figure 30 g206714 Figure 29 1. Bolt 1. Flange-head screws (1/4–20 x 5/8 inch) 3. Harness base 2. Valve mount 4. Flange nuts (1/4 inch) 2. Harness base 3. Use the previously removed bolts to secure the harness base to the console (Figure 31). 2.
PAGE 13
pressure; it is normal to see foam-marker solution and bubbles around the pressure-relief valve. Clean the pressure-relief valve periodically to maintain proper function of the valve. 8 Finishing the Installation of the Kit 1 2 No Parts Required Procedure 1. Move the prop rod for the seats into the slots and tilt the seats down. 2. Connect the positive (red) cable to the positive (+) battery post and the negative (black) cable to the negative (–) battery post using the bolts and nuts.
PAGE 14
Notes:
PAGE 15
Notes:
PAGE 16