Installation Instructions

ManualsBrandsToro ManualsSprayersX25 Monitor Visor Kit, Multi Pro 1750 or 5800 Turf Sprayer with GeoLink Precision Spray System

FormNo.3411-705RevB

X25orX30MonitorVisorKit

MultiPro

1750or5800TurfSprayerwithGeoLink

Precision

SpraySystem

ModelNo.136-0461

ModelNo.136-0462

InstallationInstructions

Usetheappropriatekitforyourmonitorasfollows:

•X25monitor—ModelNo.136-0461

•X30monitor—ModelNo.136-0462

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachineforinstallation.

Monitorvisor1

Threadedstandoff

Adhesivestrip2

Installthemonitorvisor.

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

g223646

Figure1

InstallingtheMonitorVisor

ApplyingtheAdhesiveStripsto

theX25SprayerMonitor

1.Removethebackingfromthe2adhesivestrips.

2.Atthetopofthesprayermonitor,alignthestrips

tothesprayermonitorasshowninFigure2.

3.Firmlypresstheadhesivestripstothetopofthe

monitor.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3411-705*B

Summary of content (4 pages)

PAGE 1
Form No. 3411-705 Rev B X25 or X30 Monitor Visor Kit Multi Pro® 1750 or 5800 Turf Sprayer with GeoLink® Precision Spray System Model No. 136-0461 Model No. 136-0462 Installation Instructions Use the appropriate kit for your monitor as follows: WARNING • X25 monitor—Model No. 136-0461 CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. • X30 monitor—Model No.
PAGE 2
Applying the Adhesive Strips to the X30 Sprayer Monitor 1. Remove the backing from the 2 adhesive strips. 2. At the back of the sprayer monitor, align the adhesive strips to the sprayer monitor as shown in Figure 3. 3. Firmly press the adhesive strips to the back of the monitor. g198909 Figure 2 1. 51 mm (2 inches) 3. X25 sprayer monitor (back side) 2. Adhesive strips g034896 Figure 3 2 1. 51 mm (2 inches) 3. Adhesive strips 2. 13 mm (1/2 inch) 4.
PAGE 3
Assembling the Display Hood to the X25 Sprayer Monitor 1. for the nut portion of the threaded standoff (Figure 5). At the back of the sprayer monitor and with the 2 connectors (26 pin) aligned down, remove the top locknut (5 mm) from the stud for the ball-pivot fitting (A of Figure 4). g031280 Figure 5 1. Thread-locking compound (wicking—medium-high strength)—nut threads of the threaded standoff 2. Thread-locking compound (wicking—medium-high strength)—stud threads 3.
PAGE 4
Assembling the Display Hood to the X30 Sprayer Monitor 1. for the nut portion of the threaded standoff (Figure 7). At the back of the sprayer monitor and with the 2 connectors (26 pin) aligned down, remove the top locknut (5 mm) from the stud for the ball-pivot fitting (A of Figure 6). g031280 Figure 7 1. Thread-locking compound (wicking—medium-high strength)—nut threads of the threaded standoff g034899 3.