Installation Instructions

ManualsBrandsToro ManualsUtility VehicleToro 136-1599

FormNo.3415-323RevA

MudPumpSpeedControlKit

DD4045DirectionalDrill

ModelNo.136-1599

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

PreparingtheMachine

1.Movethemachinetoalevelsurface.

2.Shutofftheengineandremovethekey.

3.Setthebattery-disconnectswitchtotheOFFposition.

InstallingtheKit

LooseParts

1x2x

2x(washer)

2x(nut)

1x1x1x

1x1x10x

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3415-323*A

Summary of content (8 pages)

PAGE 1
Form No. 3415-323 Rev A Mud Pump Speed Control Kit DD4045 Directional Drill Model No. 136-1599 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Preparing the Machine 1. Move the machine to a level surface. 2. Shut off the engine and remove the key. 3. Set the battery-disconnect switch to the OFF position.
PAGE 2
Installing the Microprocessor Important: Do not route the wire harness near moving parts where it will be pinched or cut.
PAGE 3
1. Drill 2 holes into the panel (Figure 2) using the measurements from Figure 3. g212414 Figure 3 1. 3-1/2 inches from the top edge to the center of the hole. 3. 5-1/8 inches from the edge of the panel to the center of the hole. 2. 5-11/16 inches from the center of 1 hole to the center of the other hole. 2. Secure the microprocessor to the panel (Figure 2) using 2 bolts (1/4 x 2 3/4 inches), 2 washers, and 2 nuts (1/4 inch) as shown in Box A of Figure 4. 3.
PAGE 4
Connecting the Wire Harness to the Hydrostat Pump 1. Route the wire harness down to the hydrostat pump. 2. Remove the current wire harness from the hydrostat pump (Box A of Figure 5). 3. Plug the current wire harness into the new wire harness (Box B of Figure 5). 4. Install the new wire harness connector in the hydrostat pump (Box C of Figure 5).
PAGE 5
Disconnecting the Transducer Route the wire harness along the frame with the current wire harnesses (Figure 6 and Figure 7).
PAGE 6
1. Locate the transducer below the bulkhead, just above the fuel-tank sending unit (Figure 7). 2. Disconnect the wire harness from the transducer fitting (Box A of Figure 8). 3. Remove the transducer assembly and fitting currently installed (Box A of Figure 8). 4. Install the cap onto the port (Box B of Figure 8). 5. Move the current harnesses over to the frame and connect it to the new wire harness (Box C of Figure 8). 6. Secure the wire harness using cable ties.
PAGE 7
1. Remove the hose from the fitting on the rear control weldment (Box A of Figure 10). g213031 Figure 10 2. Remove the fitting from the rear control weldment (Box B of Figure 10). 3. Install the tee fitting on the rear control weldment (Box C of Figure 10). 4. Install the hose onto the tee fitting (Box D of Figure 10). 5. Install the fitting removed in 2, shown in Box B of Figure 10 (Box A of Figure 11). g213032 Figure 11 6. Install the reducer and O-rings (Box B of Figure 11). 7.
PAGE 8
9. If the harness does not fit into the transducer, connect the harness and transducer using the adapter (Figure 13). g213030 Figure 13 Connect the Wire Harness to the Mud Pump Sensor Route the harness to the mud pump sensor (Boxes A and B of Figure 14) at the rear of the machine. g213044 Figure 14 1. Disconnect the current harness (Box A of Figure 15). 2. Connect the current harness to the new harness (Box B of Figure 15). 3. Connect the new harness to the mud pump sensor (Box C of Figure 15).