Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 136-1654

FormNo.3406-422RevC

BucketMountKit

Titan

HDSeriesRidingMower

ModelNo.136-1654

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal136-1680

136-1680

1.Maximumweightis11kg(25lb)

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-422*C

Summary of content (8 pages)

PAGE 1
Form No. 3406-422 Rev C Bucket Mount Kit Titan® HD Series Riding Mower Model No. 136-1654 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Upper mount Main bracket Top bracket Lower support bracket Welded support bracket Carriage bolt (5/16 x 7/8 inch) Nut (5/16 inch) Knob Fist clamp Slotted screw Locknut Bolt (5/16 x 1 inch) Nut (5/16 inch) Carriage bolt (5/16 x 7/8 inch) 1 1 1 1 1 4 3 1 1 1 1 3 4 1 Front-weight kit (sold seperately) 1 Prepare the machine. Install the kit. Mount the kit to the machine.
PAGE 3
Assembling the Kit Assemble the kit as shown in Figure 2. Ensure to loosely install the upper mount to the main bracket; refer to Figure 3 to determine which hole to use in the upper mount. Note: Install the lower support bracket only if you are mounting the kit in front of the rear tires. Install the bracket so that the large face is oriented rearward on the machine; Figure 2 shows the bracket orientation for mounting the kit on the left side of the machine. g037140 Figure 2 1. Main bracket 4.
PAGE 4
g037081 Figure 3 1. Use this hole if you are mounting the kit in front of the left, 3. Use this hole if you are mounting the kit in front of the right, rear tire. rear tire. 2. Use this hole if you are mounting the kit in any location behind the rear tires. Mounting the Kit to the Machine Mounting Locations You can mount this kit in 6 locations on the machine (Figure 4). Refer to 1 of the following procedures to mount the kit in the desired location.
PAGE 5
Mounting the Kit in Front of the Rear Tires 1. Secure the mount assembly to the console cover using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 5 or Figure 6. 2. Tighten the fasteners securing the upper mount to the main bracket. 3. Secure the lower support bracket to the rear side of the bracket under the console cover using 1 bolt (5/16 x 1 inch) and 1 nut (5/16 inch) as shown in Figure 5 or Figure 6.
PAGE 6
Mounting the Kit to the Side of the Engine Guard 1. Secure the mount assembly to the side upper guard using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 7 or Figure 8. 2. Tighten the fasteners securing the upper mount to the main bracket. 3. Secure the bottom of the main bracket to the engine guard using 1 carriage bolt (5/16 x 7/8 inch) and 1 nut (5/16 inch) as shown in Figure 7 or Figure 8. g213523 Figure 7 Mounting the kit to the left side of the engine guard 1. Nut (5/16 inch) 4.
PAGE 7
Mounting the Kit to the Rear Engine Guard 1. Secure the mount assembly to the rear upper guard using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 9 or Figure 10. 2. Tighten the fasteners securing the upper mount to the main bracket. 3. Secure the bottom of the main bracket to the rear engine guard using 1 carriage bolt (5/16 x 7/8 inch) and 1 nut (5/16 inch) as shown in Figure 9 or Figure 10.
PAGE 8
Installing a Front-Weight Kit Mounting a Bucket 1. Loosen the knob and raise the top bracket. Tighten the knob to hold it in place (Figure 12). For Machines with 2 or More Accessory-Mount Kits 2. Place the bottom lip of the bucket over the bottom ledge of the welded support bracket (Figure 12). If 2 or more accessory-mount kits (i.e., bucket kit or universal mount kit) are added to any of the 4 locations shown in Figure 11, add a front-weight kit.