Installation Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 136-1664

FormNo.3406-438RevC

UniversalMountKit

Titan

HDSeriesRidingMower

ModelNo.136-1664

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedorlost.

decal136-1672

136-1672

1.Warning—donotstep;noriders.

decal136-1680

136-1680

1.Maximumweightis11kg(25lb)

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-438*C

Summary of content (12 pages)

PAGE 1
Form No. 3406-438 Rev C Universal Mount Kit Titan® HD Series Riding Mower Model No. 136-1664 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Upper mount Main bracket Top bracket Lower support bracket Welded support bracket Carriage bolt (5/16 x 7/8 inch) Nut (5/16 inch) Knob Hinge bracket Nut (1/4 inch) Bolt (1/4 x 4-1/4 inches) Bolt (5/16 x 1 inch) Nut (5/16 inch) Carriage bolt (5/16 x 7/8 inch) 1 1 1 1 1 4 3 1 1 1 1 3 4 1 Front-weight kit (sold seperately) 1 Prepare the machine. Install the kit.
PAGE 3
Assembling the Kit Assemble the kit as shown in Figure 2. Ensure to loosely install the upper mount to the main bracket; refer to Figure 3 to determine which hole to use in the upper mount. Note: Do not overtighten the bolt (1/4 x 4-1/4 inches) and nut (1/4 inch); the hinge bracket must pivot freely. Note: Install the lower support bracket only if you are mounting the kit in front of the rear tires.
PAGE 4
g037081 Figure 3 1. Use this hole if you are mounting the kit in front of the left, 3. Use this hole if you are mounting the kit in front of the right, rear tire. rear tire. 2. Use this hole if you are mounting the kit in any location behind the rear tires. Mounting the Kit to the Machine Mounting Locations You can mount this kit in 6 locations on the machine (Figure 4). Refer to 1 of the following procedures to mount the kit in the desired location.
PAGE 5
Mounting the Kit in Front of the Rear Tires 1. Secure the mount assembly to the console cover using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 5 or Figure 6. 2. Tighten the fasteners securing the upper mount to the main bracket. 3. Secure the lower support bracket to the rear side of the bracket under the console cover using 1 bolt (5/16 x 1 inch) and 1 nut (5/16 inch) as shown in Figure 5 or Figure 6.
PAGE 6
Mounting the Kit to the Side of the Engine Guard 1. Secure the mount assembly to the side upper guard using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 7 or Figure 8. 2. Tighten the fasteners securing the upper mount to the main bracket. 3. Secure the bottom of the main bracket to the engine guard using 1 carriage bolt (5/16 x 7/8 inch) and 1 nut (5/16 inch) as shown in Figure 7 or Figure 8. g213949 Figure 7 Mounting the kit to the left side of the engine guard 1. Nut (5/16 inch) 4.
PAGE 7
Mounting the Kit to the Rear Engine Guard 1. Secure the mount assembly to the rear upper guard using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 9 or Figure 10. 2. Tighten the fasteners securing the upper mount to the main bracket. 3. Secure the bottom of the main bracket to the rear engine guard using 1 carriage bolt (5/16 x 7/8 inch) and 1 nut (5/16 inch) as shown in Figure 9 or Figure 10.
PAGE 8
Installing a Front-Weight Kit Mounting a Bucket Note: If desired, you can remove the hinge bracket and mount the bucket using the welded support bracket. For Machines with 2 or More Accessory-Mount Kits 1. Loosen the knob and raise the top bracket. Tighten the knob to hold it in place (Figure 12). If 2 or more accessory-mount kits (i.e., bucket kit or universal mount kit) are added to any of the 4 locations shown in Figure 11, add a front-weight kit.
PAGE 9
Securing the Hinge Bracket 1. Raise the hinge bracket. 2. Loosen the knob and lower the top bracket, inserting the tab into the notch in the hinge bracket (Figure 13). 3. Tighten the knob. g037423 Figure 13 1. Tab in top bracket 2.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12