Installation Instructions

ManualsBrandsToro ManualsSprayersPump Service Kit, Multi Pro WM or 5800 Series Turf Sprayer

FormNo.3406-827RevA

PumpServiceKit

MultiPro

1750,5800,WMTurfSprayers

ModelNo.136-2253

ModelNo.136-2254

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Notethepositionofthettings.

Pump1

Fitting31.8mm(1-1/4inches)

O-ring—38x46mm(1-1/2x1-13/16

inches)

Retainer—84x48mm(3-5/16x1-7/8

inches)

Fitting38.1mm(1-1/2inches)

O-ring—45x53mm(1-3/4x2-3/32

inches)

Retainer—106.5x73mm(4-3/16x

2-7/8inches)

AssembletheKitSprayerPump.

Note:RefertotheServiceManualforinformationonremovingandinstallingthesprayerpump.

PreparingtheMachine

NoPartsRequired

Procedure

1.Movethemachinetoalevelsurface(AandBofFigure

1).

Figure1

2.Settheparkingbrake(CofFigure1).

3.Shutofftheengine(DofFigure1).

4.Removethekeyfromthekeyswitch(EofFigure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-827*A

Summary of content (4 pages)

PAGE 1
Form No. 3406-827 Rev A Pump Service Kit Multi Pro® 1750, 5800, WM Turf Sprayers Model No. 136-2253 Model No. 136-2254 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty. No parts required – Prepare the machine. No parts required – Note the position of the fittings. Pump Fitting 31.
PAGE 2
Noting the Position of the Sprayer-Pump Fittings No Parts Required Procedure 1. With the old sprayer pump removed from the machine, note the position of the retainer and retainer sockets of the pressure-port fitting; refer to Figure 2 or Figure 3. Figure 3 Multi Pro 5800 and Multi Pro WM Machines 1. Supply-port fitting 2. Pressure-port fitting 2. Note the position of the retainer and retainer sockets of the supply-port fitting; refer to Figure 2 or Figure 3. Figure 2 Multi Pro 1750 Machines 1.
PAGE 3
Assembling the Kit Sprayer Pump Parts needed for this procedure: 1 Pump 1 Fitting 31.8 mm (1-1/4 inches) 1 O-ring—38 x 46 mm (1-1/2 x 1-13/16 inches) 1 Retainer—84 x 48 mm (3-5/16 x 1-7/8 inches) 1 Fitting 38.1 mm (1-1/2 inches) 1 O-ring—45 x 53 mm (1-3/4 x 2-3/32 inches) 1 Retainer—106.5 x 73 mm (4-3/16 x 2-7/8 inches) Figure 5 Multi Pro 1750 1. Pressure port 3. Retainer socket 2. Fitting 31.8 mm (1-1/4 inches) Assembling the Pump 1.
PAGE 4
Figure 7 Multi Pro 1750 1. Fitting 38.1 mm (1-1/2 inches) 3. Retainer socket 2. Supply port Figure 8 Multi Pro 5800 and Multi Pro WM 1. Fitting 38.1 mm (1-1/2 inches) 3. Retainer socket 2. Supply port 7. Tighten the fitting by hand until the retainer sockets are aligned the same as you noted of the old pump in step 1 of 2 Noting the Position of the Sprayer-Pump Fittings (page 1); refer to Figure 2 or Figure 3.