Installation Instructions

ManualsBrandsToro ManualsAttachmentsSkid Plate Kit, Groundsmaster 4000 or 4100 Series Rotary Mower

FormNo.3413-386RevA

SkidPlateKit

Groundsmaster

4000or4100SeriesRotaryMower

ModelNo.136-4360

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Lowerthecuttingunits.

3.Engagetheparkingbrake.

4.Shutofftheengineandremovethekey.

5.Useajacktoraisethemachine.

Note:Therearejackingpointslocatedatthefront

andrearofthemachine;refertotheOperator’sManual

foryourmachine.

DANGER

Mechanicalorhydraulicjacksmayfailtosupport

machineandcauseaseriousinjury.

•Usejackstandswhensupportingmachine.

•Donotusehydraulicjacks.

InstallingtheSkidPlates

Partsneededforthisprocedure:

Outer-rearskidplate

1Rearskidplate

2Frontskidplate

4Lockwasher

4Hex-socketscrew

Spring-coilwasher

Bolt(M10x30mm)

Bolt(3/8-16x4inches)

4Flangenut

InstallingtheRearSkidPlates

1.Removetheexistinghardware(4boltsand4washers)

fromthemountplateasshowninFigure1.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3413-386*A

Summary of content (4 pages)

PAGE 1
Form No. 3413-386 Rev A Skid Plate Kit Groundsmaster® 4000 or 4100 Series Rotary Mower Model No. 136-4360 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. 2 Installation 1 Installing the Skid Plates Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Lower the cutting units. 3. Engage the parking brake. 4.
PAGE 2
g207711 g204660 Figure 3 Right Side Shown Figure 1 1. Bolt—existing hardware 2. Washer—existing hardware 1. Bolt 2. Axle cap 2. Use 4 bolts (M10 x 30 mm) and 4 spring-coil washers to secure the rear skid plate to the mount plate (Figure 2). 3. Axle 4. Use 2 hex-socket screws and 2 lock washers to secure the outer-rear skid plates to the axle caps on both sides of the machine (Figure 4). g204659 Figure 2 1. Bolt (M10 x30 mm) 3. Rear skid plate 2. Spring-coil washer 3.
PAGE 3
Installing the Front Skid Plates 1. Remove the existing hardware (2 bolts and 2 nuts) from the manifold on the left side of the machine (Figure 5) g205111 Figure 5 Left Side Shown 1. Bolt—existing hardware 5. Bolt (3/8-16 x 4 inches) 2. Manifold 6. Front skid plate 3. Hub bracket 7. Flange nut 4. Nut—existing hardware 2. Align the holes in a front skid plate with the holes in the manifold (Figure 5). 3.
PAGE 4
. Repeat steps 1 through 3 to install the other front skid plate to the right side of the machine (Figure 6). g205112 Figure 6 Right Side Shown 1. Bolt—existing hardware 5. Bolt (3/8-16 x 4 inches) 2. Manifold 6. Front skid plate 3. Hub bracket 7. Flange nut 4.