Installation Instructions

ManualsBrandsToro ManualsCompact Utility LoadersLight Kit, TXL 2000 Tool Carrier

FormNo.3430-978RevA

LightKit

TXL2000ToolCarrier

ModelNo.136-4890

InstallationInstructions

Installation

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Lowertheloaderarms.

3.Shutofftheengineandremovethekey.

4.Opentherear-accesscover.

5.Turnthebattery-disconnectswitchtotheOFF

position(Figure1).

g261512

Figure1

1.Battery-disconnect

switch—OFFposition

2.Battery-disconnect

switch—ONposition

InstallingtheLights

Partsneededforthisprocedure:

2Light

Leftlightbracket

1Rightlightbracket

Switch

2Thread-cuttingscrew

Bolt(5/16x1inch)

Nut(5/16inch)

Procedure

1.Removethe2thread-cuttingscrewsandplate

fromthecontrolpanel(Figure2).Discardthe

plate.

g283294

Figure2

1.Thread-cuttingscrew(2)

2.Plate

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3430-978*A

Summary of content (8 pages)

PAGE 1
Form No. 3430-978 Rev A Light Kit TXL 2000 Tool Carrier Model No. 136-4890 Installation Instructions 2 Installation 1 Installing the Lights Preparing the Machine Parts needed for this procedure: No Parts Required Procedure 1. Park the machine on a level surface. 2. Lower the loader arms. 3. Shut off the engine and remove the key. 4. Open the rear-access cover. 5. Turn the battery-disconnect switch to the OFF position (Figure 1).
PAGE 2
. Install the left light bracket using 2 thread-cutting screws (Figure 3). 4. Install the right light bracket to the tower plate using 2 bolts (5/16 x 1 inch) and 2 nuts (5/16 inch) as shown in Figure 5. g283291 Figure 3 1. Thread-cutting screw (2) 3. 2. Left light bracket Remove the bolt, washer, and nut from a light and use them to secure the light to the bracket (Figure 4). g283292 Figure 5 1. Light bolt 5. Washer 2. Light 6. Light nut 3. Bolt—5/16 x 1 inch (2) 7. Nut—5/16 inch (2) 4.
PAGE 3
4. 3 Remove the plug from an accessory connector on the machine wire harness (P50, P75, or P76) and plug the kit wire harness to it (Figure 8). Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 2 Cable tie Procedure Refer to Figure 6 to identify the wire harness connectors. g283649 Figure 6 1. Left light connector 2. Switch connector 3. Machine wire harness connector 4. Right light connector g282599 Figure 8 1.
PAGE 4
9. Using the console plate opening to access the wire harness, route the left light connector through the hole in the left light bracket and connect it to the left light (Figure 11). g283803 Figure 9 g283780 1. Wire harness 2. Right light 3. Cable tie Figure 11 7. Secure the wire harness to the grab bar using a cable tie (Figure 9). 8. Route the left light and switch connectors through the hole on the left side of the machine (Figure 10). 10.
PAGE 5
4 5 Installing the Reflectors Completing the Installation Parts needed for this procedure: No Parts Required 2 Reflector (2 x 3 inches) 2 Reflector (1-1/2 x 6 inches) Procedure Procedure 1. Thoroughly clean the surfaces on the back of the machine and the front of the loader arms in the locations shown in Figure 13 and Figure 14. 2. Adhere the reflectors to the machine. g283844 Figure 13 1. Reflector (1-1/2 x 6 inches) g283845 Figure 14 1. Reflector (2 x 3 inches) 5 1.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8