Installation Instructions

ManualsBrandsToro ManualsAttachmentsCutting Unit Lock Kit, Reelmaster 3555 or 3575 Traction Unit

FormNo.3414-799RevA

CuttingUnitLockKit

Reelmaster

3555or3575TractionUnit

ModelNo.136-6354

InstallationInstructions

Installation

Thiskitautomaticallypreventsunevensettlingofthe

mowerdecks.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

Note:Determinetheleftandrightsidesofthe

machinefromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceandlower

thecuttingdecks.

2.Engagetheparkingbrake,shutofftheengine

andremovethekey.

InstallingtheLockManifold

Fittings

Partsneededforthisprocedure:

Lockmanifold

90-degreetting

Straighttting

Procedure

1.Threadthe90-degreettingintothe1porton

thelockmanifoldandtightenitto24.4to29.8

N·m(18to22ft-lb)asshowninFigure1.

Note:Ensurethattheopenfaceofthe

90-degreettingisfacingtowardthe2portof

thelockmanifold.

g214098

Figure1

1.90-degreetting3.Straighttting

2.Lockmanifold4.Solenoid

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3414-799*A

Summary of content (4 pages)

PAGE 1
Form No. 3414-799 Rev A Cutting Unit Lock Kit Reelmaster® 3555 or 3575 Traction Unit Model No. 136-6354 Installation Instructions Installation This kit automatically prevents uneven settling of the mower decks. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 2
Note: The notch in the bracket should point toward the right of the machine, and the wider end should pointed toward the rear end of the machine, flush with the existing bracket. 2. Thread the straight fitting into the 2 port on the lock manifold and tighten it to 24.4 to 29.8 N·m (18 to 22 ft-lb) as shown in Figure 1.
PAGE 3
5. Raise the access panel at the foot of the seat to access the wire harness connections. 6. Remove the existing wire harness socket from the S3 coil on the lift manifold (Figure 5). g213808 Figure 6 Hoses not shown for clarity g213743 Figure 5 Hoses not shown for clarity 1. Existing wire harness socket 1. Lock-manifold socket 3. Existing wire harness plug 2. S3 solenoid plug 2. S3 Coil 8. Disconnect the hose from the fitting in the C3 port. 7.
PAGE 4
g213852 Figure 8 Other hoses not shown for clarity 1. New kit hose 4. Existing hose 2. Fitting in the 2 port of the 5. Fitting in the 1 port of lock lock manifold manifold 3. Fitting in the C3 port of the lift manifold 10. Connect the kit hose from the fitting in the 2 port of the lock manifold to the fitting in the C3 port of the lift manifold (Figure 8) and tighten the nut to 24.4 to 29.8 N·m (18 to 22 ft-lb). 11. Connect the battery; refer to your Operator’s Manual.