Installation Instructions

ManualsBrandsToro ManualsMud BuggyToro 137-0591

FormNo.3414-557RevA

LiftHandleKit

MB-1600MudBuggy

ModelNo.137-0591

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheexistinglifthandle.

Pivot1

Leverplate1

Leverassembly1

Shaftguide

Pin1

Clevispin

Cotterpin(1/2inch)

Bearing2

Bolt(1/4x2-1/4inches)

Cotterpin(1inch)

Nut(1/4inch)

Installthekitlifthandle.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3414-557*A

Summary of content (4 pages)

PAGE 1
Form No. 3414-557 Rev A Lift Handle Kit MB-1600 Mud Buggy Model No. 137-0591 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 © 2017—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Lower the hopper. 4. Shut off the engine. 2 g210902 Figure 1 Removing the Existing Lift Handle 1. Clevis pin (3/16 x 1 inch) 3. U-link 2. Cotter pin 4. Handle assembly 3. Remove and discard the handle assembly (Figure 1). No Parts Required 4.
PAGE 3
Installing the Kit Lift Handle Parts needed for this procedure: g210903 Figure 2 1. Flange bolt (5/16 x 1 inch) 6. Shaft guide 2. Pivot 7. Nut (1/4 inch) 3. Cotter pin (3/4 inch) 8. Lever plate 4. Nut (5/16 inch) 9. Bolt (1/4 x 2-1/4 inches) 5. Clevis pin (3/8 x 1-3/32 inch) 1 Pivot 1 Lever plate 1 Lever assembly 1 Shaft guide 1 Pin 1 Clevis pin 1 Cotter pin (1/2 inch) 2 Bearing 1 Bolt (1/4 x 2-1/4 inches) 1 Cotter pin (1 inch) 1 Nut (1/4 inch) Procedure 1.
PAGE 4
6. Secure the handle to the lever plate using a cotter pin (1/2 inch) and the clevis pin (3/16 x 1 inch) that you removed previously (Figure 6). 2. Install the bearings into the shaft guide (Figure 3). 3. Install the kit through the shaft guide and handle assembly, and secure it using the cotter pin (1 inch) as shown in Figure 4. g210928 Figure 6 1. Cotter pin (1/2 inch) 7. Install the cowl. g210926 Figure 4 1. Handle assembly 3. Clevis pin 2. Cotter pin (1 inch) 4.