Installation Instructions

ManualsBrandsToro ManualsAttachmentsHigh Height-of-Cut Kit, Reelmaster 3000 or 5000 Series DPA Cutting Unit

FormNo.3417-887RevA

HighHeight-of-CutKit

Reelmaster

3000or5000SeriesDPACuttingUnit

ModelNo.137-0890

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparetoinstallthekit.

Nopartsrequired

–

Removingtheheight-of-cutbrackets.

Bolt(5/16x1-1/8inches)

Serrated-angenut(5/16inch)

Highheightofcutbracket(left)

Highheightofcutbracket(right)

Height-of-cutscrew(3/8x2-3/4inches)

Washer(5/16inch)

Flangelocknut(5/16)

Assembletheheight-of-cutbrackets.

Locknut(3/8inch)

Installthefrontroller.

Carriagebolts(5/16x4inches)

Shim(0.25inch)

Flangelocknut(5/16inch)

Installtherearrollershims.

Nopartsrequired

–

Finishinstallingtheheight—of-cutkitinstallation.

PreparingtoInstalltheKit

MachineswiththeCuttingUnits

Installed

1.Parkthemachineonalevelsurfaceandlower

thecuttingunits.

2.Engagetheparkingbrake,shutofftheengine,

andremovethekey.

3.Removethecuttingunits;refertothecuttingunit

Operator’sManual.

RemovingtheHeight-of-Cut

Brackets

1.Loosenthe2angelocknutsatthe2

height-of-cutscrews(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3417-887*A

Summary of content (8 pages)

PAGE 1
Form No. 3417-887 Rev A High Height-of-Cut Kit Reelmaster® 3000 or 5000 Series DPA Cutting Unit Model No. 137-0890 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare to install the kit.
PAGE 2
g234981 Figure 3 1. Carriage bolt 3. Flange locknut 2. Height-of-cut bracket g235009 Figure 1 1. Height-of-cut screw 2. 4. 2. Flange locknut Remove the height-of-cut bracket and front roller from the cutting unit (Figure 4). Loosen the 2 serrated-flange nuts and 2 bolts that secure the front roller shaft to the roller support end of the left and right height-of-cut brackets (Figure 2). g234982 Figure 4 1. Height-of-cut support (side 3. Height-of-cut bracket plate) 2.
PAGE 3
Assembling the High Height-of-Cut Brackets 1. 3. Assemble the 2 height-of-cut screw (3/8 x 2-3/4 inches), 4 washers (5/16 inch), and 2 flange locknuts (3/8 inch); refer to Figure 5. Loosely assemble a bolt (5/16 x 1-1/8 inches) and serrated-flange nut (5/16 inch) to each roller support of the high height of cut brackets (Figure 5). Note: Align the serrations of the nut toward the roller support.
PAGE 4
g234977 Figure 10 1. Carriage bolt g235085 2. Height-of-cut support (side 6. Flange locknut (3/8 inch) plate) Figure 8 3. Flange locknut 1. Height-of-cut screw 5. Flange locknut 3. Height-of-cut screw 7. Height of cut bracket 2. Washer 4. Washers 8. Front roller shaft 2. 4. Assemble the height of cut bracket to the support with the carriage bolt (Figure 10) that you removed in step 3 of Removing the Height-of-Cut Brackets (page 1) and a locknut (3/8 inch). 5.
PAGE 5
Installing the Rear Roller Shims 1. Remove the 4 flange locknuts, 4 washers, and 4 carriage bolts that secure the rear roller and shims to the flange of the side plate (Figure 12). Note: Retain the washers and shims for installation in step 6. g234980 Figure 13 1. Carriage bolt (5/16 x 4 inches) 4. Rear roller bracket 2. Flange locknut (5/16 inch) 5. Spacers (stored position) 3. Washer 6. Spacers (height–of–cut position) Note: You can order spacers Part No.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8