Installation Instructions

ManualsBrandsToro ManualsRiding ProductsBattery Cable Kit, Groundsmaster 5900 or 5910 Rotary Mower

FormNo.3416-805RevA

BatteryCableKit

Groundsmaster

5900or5910RotaryMower

ModelNo.137-5470

InstallationInstructions

Installation

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemical

orchemicalsknowntotheStateof

Californiatocausecancer,birthdefects,

orreproductiveharm.

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Loweralldeckstotheground.

3.Engagetheparkingbrake.

4.Shutofftheengineandremovethekey.

5.Allowthemachinetocool.

AccessingtheBattery

Compartment

Note:Retainallpartsremovedunlessotherwise

directed.

1.Disconnectthebatteryusingthe

battery-disconnectswitch;refertoyour

Operator’sManual.

2.Remove3angescrewsfromeachsideofthe

rearbumperasshownin(Figure1).

Important:Supportthebumpersothatit

willnotfallbeforeremovinganyfasteners.

3.Loosentheremainingangescrewssecuring

therearbumpertotheframeandpivotthe

bumperdownward.

g199824

Figure1

1.Rearbumper

3.Flangescrew(loosenon

bothsides)

2.Flangescrews(remove

frombothsides)

4.Loosentheknobsandremovebothsidepanels

(Figure2).

g199825

Figure2

1.Knobs

2.Sidepanel

5.Loosenthe4angescrewsonthebottomofthe

rearshroudandremovethe2angescrewson

eachside(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3416-805*A

Summary of content (4 pages)

PAGE 1
Form No. 3416-805 Rev A Battery Cable Kit Groundsmaster® 5900 or 5910 Rotary Mower Model No. 137-5470 Installation Instructions Installation WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. g199824 Preparing the Machine 1. Park the machine on a level surface. 2. Lower all decks to the ground. 3. Engage the parking brake. 4. Shut off the engine and remove the key. 5.
PAGE 2
g221203 Figure 3 1. Rear shroud 3. Flange screws (remove from both sides) g221400 Figure 5 2. Flange screws (loosen these) 6. 1. Positive battery jump post 3. 12VDC Alternator 2. Existing cable routing 4. Alternator cable connection Remove the 4 screws that secure the battery cover to the machine and remove the cover (Figure 4). g221204 Figure 4 1. Battery cover 2. Screw Installing the Cables 1.
PAGE 3
2. Install the 3-terminal cable and torque the nuts as shown in Figure 7, Figure 8, and Figure 9. Note: Secure the cable to the frame with cable ties as needed. You may use the red tape that connected the previous cable to the frame as a guide. g221414 g221415 Figure 7 Some parts not shown for clarity 1. 3-terminal cable routing Figure 9 1. Battery disconnect switch connection (torque nut to 27 N·m (20 ft-lb)) 3. Alternator cable connection (torque nut to 15 N·m (11 ft-lb)) 2.
PAGE 4
3. Completing the Installation Install the 2-terminal cable and torque the nuts as shown in (Figure 10). Note: Secure the cable to the frame with cable 1. Install the battery cover using the screws removed in step 6 of Accessing the Battery Compartment (page 1). 2. Install the rear shroud using the flange screws removed in step 5 of Accessing the Battery Compartment (page 1). 3. Install the side panels using the knobs removed in step 4 of Accessing the Battery Compartment (page 1). 4.