Installation Instructions

ManualsBrandsToro ManualsRiding ProductsPower Harness Kit, Groundsmaster 5900 Series Rotary Mower

FormNo.3423-326RevB

PowerHarnessKit

Groundsmaster

5900SeriesRotaryMower

ModelNo.138-3002

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Disconnectthebattery.

Nopartsrequired

–

Removethesidepanel.

Solenoid

Bolt(1/4x3/4inch)

Flangelocknut2

Fuse-holder1

Jumperstrap1

Fuse(100A)

Flangenut(8mm)

Flangenut(5/16inch)

Redinsulator1

Installthefuseholderandsolenoid.

Nopartsrequired

–

Connectthesolenoidandfuseholder.

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Installthesidepanelandclosethe

hood.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3423-326*B

Summary of content (8 pages)

PAGE 1
Form No. 3423-326 Rev B Power Harness Kit Groundsmaster® 5900 Series Rotary Mower Model No. 138-3002 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 © 2018—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty. Use No parts required – Prepare the machine. No parts required – Disconnect the battery. No parts required – Remove the side panel.
PAGE 2
1 3 Preparing the Machine Removing the Side Panel No Parts Required No Parts Required Procedure Procedure CAUTION 1. If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or bystanders. Loose the 2 knobs that secure the right side panel to the machine (Figure 2). Remove the key from the ignition switch before you do any maintenance. 1. 2. 3. 4. Park the machine on a level surface. Engage the parking brake. Lower the cutting units.
PAGE 3
4 Installing the Fuse Holder and Solenoid Parts needed for this procedure: 1 Solenoid 2 Bolt (1/4 x 3/4 inch) 2 Flange locknut 1 Fuse-holder 1 Jumper strap 1 Fuse (100 A) 2 Flange nut (8 mm) 2 Flange nut (5/16 inch) 1 Red insulator g251782 Figure 4 1. Bolt (1/4 x 3/4 inch) 3. Electrical bracket 2. Solenoid 4. Flange locknut (1/4 inch) 2. Secure the solenoid to the bracket (Figure 4) with the 2 bolts (1/4 x 3/4 inch) and 2 flange locknuts (1/4 inch). 3.
PAGE 4
5 Connecting the Solenoid and Fuse Holder No Parts Required Connecting the Solenoid and Fuse Block 1. Install the pink-wire connector labeled COIL + [CAB CONTACTOR ] to the left post at the bottom of the solenoid (Figure 6). g251806 Figure 7 1. Jumper strap 5. 2. Insulator Assemble the jumper strap and insulator onto the right post of the fuse-holder and right post of the solenoid (Figure 8). g251781 Figure 6 1. Solenoid (left post) 4. Ring terminal (2 red wires) 2.
PAGE 5
Connecting the Fuse and Wiring 1. 6 Assemble the fuse (100 A) onto the left and right posts of the fuse-holder (Figure 9). Connecting the Battery No Parts Required Procedure Rotate the battery disconnect switch to the ON position; refer to the Operator’s Manual for your machine. 7 Installing the Side Panel and Closing the Hood g251779 Figure 9 1. Flange nuts (8 mm) 3. Fuse (100 A) 2. Ring terminal (yellow wire) 4. Right post (fuse-holder) 2. 3.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8