Installation Instructions

ManualsBrandsToro ManualsLawn MowersToro 138-4890

FormNo.3421-500RevB

HeightofCutLatchingKit

Grandstand

Mowers

ModelNo.138-4890

InstallationInstructions

Safety

SafetyandInstructional

Decals

Safetydecalsandinstructionsare

easilyvisibletotheoperatorandare

locatednearanyareaofpotential

danger.Replaceanydecalthatis

damagedormissing.

decal131-3521

131-3521

1.Heightofcut

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3421-500*B

Summary of content (8 pages)

PAGE 1
Form No. 3421-500 Rev B Height of Cut Latching Kit Grandstand® Mowers Model No. 138-4890 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal131-3521 131-3521 1. Height of cut © 2018—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the existing plates. Latch plate Shoulder bolt Washer-head shoulder bolt Washer Nut (3/8 inch) Nut (1/4 inch) Wear plug Spacer (1.7 inches) Spacer (2.7 inches) Inner plate Spacer (0.
PAGE 3
2 3 Removing the Existing Plates Installing the Latch Plate Parts needed for this procedure: 1 Latch plate 1 Shoulder bolt 1 Washer-head shoulder bolt Remove the fuel tank; refer to the Operator’s Manual for the machine. 2 Washer 1 Nut (3/8 inch) Use the height-of-cut lever to lower the mower deck onto wood blocks. 1 Nut (1/4 inch) 1 Wear plug No Parts Required Procedure 1. 2. 3. Remove both plates and fasteners as shown in Figure 1. Procedure 1.
PAGE 4
g255884 Figure 3 1. Drill the hole (3/8 inch) here. 2. Template 3. Drill a hole (3/8 inch) into the lever at the location shown in Figure 3. 4. Install the new latch plate using 1 shoulder bolt, 1 washer-head shoulder bolt, 2 washers, 1 nut (3/8 inch), 1 nut (1/4 inch) as shown in Figure 4. Note: Ensure that the washers seat onto the shoulder of the bolt and are not pinched between the height-of-cut lift arm and the shoulder of the bolt. g246976 Figure 4 1. Shoulder bolt 5. Nut (3/8 inch) 2.
PAGE 5
4 Installing the New Plates Parts needed for this procedure: 2 Spacer (1.7 inches) 1 Spacer (2.7 inches) 1 Inner plate 2 Spacer (0.7 inch) 1 Outer plate 3 Washer 3 Bolt (3/8 x 3-3/4 inches) 4 Nut (3/8 inch) 1 Pin g247029 Figure 5 Procedure 1. 2. Install the inner and outer plates to the machine using the spacers, washers, bolts, and nuts as shown in Figure 5. 1. Inner plate 6. Outer plate 2. Spacer—0.7 inch (2) 7. Spacer—2.7 inches 3. Washer (3) 8. Spacer—1.7 inches (2) 4.
PAGE 6
Notes:
PAGE 7
g255885
PAGE 8