Installation Instructions

ManualsBrandsToro ManualsRiding ProductsHydraulic Filter Relocation Kit, Reelmaster 3550 or 3555 Traction Unit

FormNo.3423-950RevB

HydraulicFilterKit

Reelmaster

3550or3555TractionUnit

ModelNo.138-6942

InstallationInstructions

Safety

WARNING

Hydraulicuidescapingunderpressurecan

penetrateskinandcauseinjury.

•Seekimmediatemedicalattentionifuidis

injectedintoskin.Injecteduidmustbe

surgicallyremovedwithinafewhoursby

adoctor.

•Ensurethatallhydraulic-uidhoses

andlinesareingoodconditionandall

hydraulicconnectionsandttingsaretight

beforeapplyingpressuretothehydraulic

system.

•Keepyourbodyandhandsawayfrom

pin-holeleaksornozzlesthateject

high-pressurehydraulicuid.

•Usecardboardorpapertondhydraulic

leaks.

•Safelyrelieveallpressureinthehydraulic

systembeforeperforminganyworkonthe

hydraulicsystem.

PreparingtheMachine

1.Parkthemachineonalevelsurface.

2.Lowerthecuttingunits.

3.Engagetheparkingbrake.

4.Shutofftheengine,andremovethekey.

InstallingtheKit

Note:Installthefastenersandhydraulicttings

looselytofacilitateassembly.Tighteneverythingafter

allpartsareinstalled.

1.Drainthehydraulicsystem;refertothetraction

unitOperator’sManual.

2.Removeanddiscardthehydraulictubethat

connectsthelterheadtothehydraulictank

(Figure1).

g256655

Figure1

1.Hydraulictube3.Filterhead

2.Hydraulictank

3.Removethettingfromtheothersideofthe

lterhead(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3423-950*B

Summary of content (4 pages)

PAGE 1
Form No. 3423-950 Rev B Hydraulic Filter Kit Reelmaster® 3550 or 3555 Traction Unit Model No. 138-6942 Installation Instructions Safety Preparing the Machine WARNING Hydraulic fluid escaping under pressure can penetrate skin and cause injury. • Seek immediate medical attention if fluid is injected into skin. Injected fluid must be surgically removed within a few hours by a doctor.
PAGE 2
Note: Install the filter head so that the straight fitting is oriented toward the rear of the machine and the angled fitting is oriented toward the front of the machine. g256658 g256652 Figure 3 g256657 Figure 2 1. Flange-head bolts 4. Filter head 2. Bracket 3. Fitting 5. Filter 4. Remove and discard the 2 flange-head bolts and 2 flange nuts securing the bracket to the frame of the traction unit and remove the bracket with the filter head attached. 5.
PAGE 3
g256656 g256653 Figure 4 1. Flange-head bolts (5/16 x 1 inch) 3. Bracket 2. Flange nuts (5/16 inch) 9. Loosely install the large fitting of the new hydraulic tube to the 45° fitting on the filter head and the small fitting of the new hydraulic tube to the 45° fitting on the hydraulic tank (Figure 5). g257860 Figure 6 Torque sequence Note: Discard the existing O-rings and install the new O-rings. 1. 110 to 134 N∙m (81 to 99 ft-lb) 4. 115 to 142 N∙m (85 to 105 ft-lb) 2.
PAGE 4