Installation Instructions

ManualsBrandsToro ManualsRiding ProductsDriveplate Kit, Reelmaster 5410/5510/5610-D or Groundsmaster 4300-D Series Traction Unit with Yanmar Engine

FormNo.3425-668RevA

DriveplateKit

Reelmaster

5410/5510/5610-DorGroundsmaster

4300-DSeries

TractionUnitwithYanmarEngine

ModelNo.138-6973

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethehoodsaddleanddrive-lineguard.

Nopartsrequired

–

Removethedriveshaftandywheel-adapterplate.

Flywheel-adapterplate1

Backupplate1

Capscrew(3/8x1inch)

Flangelocknut(3/8inch)

Replacetheywheel-adapterplate.

Flange-headcapscrew8

Backupring2

Installthedriveshaftandywheel-adapterplate.

Nopartsrequired

–

Installthedrive-lineguardandhoodsaddle.

Nopartsrequired

–

Finishthekitinstallation.

PreparingtheMachine

CAUTION

Ifyouleavethekeyintheswitch,someone

couldaccidentlystarttheengineand

seriouslyinjureyouorotherbystanders.

Removethekeyfromtheswitchbeforeyou

performanymaintenance.

1.Parkthemachineonalevelsurface,engage

theparkingbrake,lowerthecuttingunits,shut

offtheengine,removethekey,andwaitforall

movementtostopbeforeleavingtheoperator’s

seat.

2.Unlatchandtiptheoperator’sseat.

3.Unlatchandopenthehood.

RemovingtheHoodSaddle

andDrive-LineGuard

1.Liftthehoodsaddlefromthesaddlebrackets,

andremovehoodsaddlefromthemachine

(Figure1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3425-668*A

Summary of content (8 pages)

PAGE 1
Form No. 3425-668 Rev A Driveplate Kit Reelmaster® 5410/5510/5610-D or Groundsmaster® 4300-D Series Traction Unit with Yanmar Engine Model No. 138-6973 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare the machine.
PAGE 2
g037404 Figure 2 g266478 Figure 1 1. Hood saddle 4. Flange nut and capscrew 2. Drive-line guard 5. Heat shield Remove the 2 flange nuts that secure the drive-line guard to the heat shield and guard bracket, and remove the guard (Figure 1). 4. Bolt (2) 2. Separate the driveshaft yolk from the pump (Figure 2). 3.
PAGE 3
Replacing the Flywheel-Adapter Plate Removing the Driveshaft from the Flywheel-Adapter Plate 1. Remove the 6 capscrews and 6 flange locknuts that secure the flywheel-adapter plate and backup plate to the driveshaft (Figure 5). Discard the 6 capscrews and 6 nuts that you removed. g037517 Figure 3 1. Flange-head capscrew (8) 3. Flywheel (engine) 2.
PAGE 4
Assembling the Driveshaft to the Flywheel-Adapter Plate 1. Assemble the driveshaft to the flywheel-adapter plate and backup plate (Figure 6) with the 6 capscrew (3/8 x 1 inch) and 6 flange locknut (3/8 inch). g266463 Figure 7 1. Flange-head capscrew 3. Flywheel (engine) 2. Flywheel-adapter plate 4. Backup rings 3. Assembling the Driveshaft to the Hydraulic Pump g266464 Figure 6 1. Flange locknut (3/8 inch) 4. Backup plate 2. Driveshaft 5.
PAGE 5
Installing the Drive-Line Guard and Hood Saddle 1. Align the holes in the drive-line guard with the capscrew in the guard bracket and heat shield (Figure 9). g242201 Figure 10 1. Heat shield 4. Tighten the flange nut and capscrews securing the drive-line guard and heat shield to the bracket (Figure 9). 5. Assemble the hood saddle onto the saddle brackets (Figure 9). Finishing the Kit Installation g266478 Figure 9 1. Hood saddle 4. Flange nut and capscrew 2. Drive-line guard 5. Heat shield 3.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8