Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSafety Chain Kit, Tow-Behind Products

FormNo.3431-697RevA

SafetyChainKit

Tow-BehindProducts

ModelNo.139-3179

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Getthemachineready.

Safetychain

Capscrew(1/2x5-1/2inches)

Washer4

Flangebushing(Models07053,07055,

07068,44507,44701,44552,44552TE,

44554and44751)

Flangelocknut(1/2inch)

Installthechains.

GettingtheMachineReady

NoPartsRequired

PreparingtheMachine

Model31905

1.Connectthemachinetothetowvehicle;referto

theOperator'sManualforthemachine.

2.Lowerthemowerdecks;refertotheOperator’s

Manualforyourmachine.

3.Engagetheparkingbrakeforthetowvehicle,

shutofftheengine,removethekey,andwait

forallmovingpartstostopbeforeleavingthe

operator’sseat.

4.Chockthetiresofthemachine.

5.Lowerthejackandsupportthemachine;referto

theOperator'sManualforthemachine.

Important:Youmustfullysupportthe

weightofthemachinewiththejack.

6.Disconnectthemachinefromthetowvehicle.

PreparingtheMachine

Models07053,07055,07068,44507,44701,

44552,44552TE,44554and44751

1.Ifconnectedtoatowvehicle,engagethe

parkingbrakeforthetowvehicle,shutoffthe

engine,removethekey,andwaitforallmoving

partstostopbeforeleavingtheoperator’sseat.

2.Chockthetiresofthemachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3431-697*A

Summary of content (4 pages)

PAGE 1
Form No. 3431-697 Rev A Safety Chain Kit Tow-Behind Products Model No. 139-3179 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – 2 Safety chain Capscrew (1/2 x 5-1/2 inches) Washer Flange bushing (Models 07053, 07055, 07068, 44507, 44701, 44552, 44552TE, 44554 and 44751) Flange locknut (1/2 inch) 2 1 4 Get the machine ready. Install the chains.
PAGE 2
3. If the machine is not connected to a tow vehicle, support the machine so that the tongue is clear of the ground; refer to the Operator's Manual for the machine. 2 Installing the Safety Chains g280660 Figure 2 1. Safety chain 4. Capscrew (1/2 x 5-1/2 inches) Safety chain 2. Washer (1/2 inch) 5. Clevis 1 Capscrew (1/2 x 5-1/2 inches) 3.
PAGE 3
Operation Connecting the Safety Chains to the Tow Vehicle 1. Assemble the mower to the tow vehicle; refer to the Operator’s Manual for the mower. 2. Assemble the spring hook of the right safety chain to the safety chain anchor point at the left side of the tow vehicle (Figure 5). Important: The safety chains must cross each other below the hitch. g286826 Figure 4 1. Flange locknut (1/2 inch) 3. Capscrew (1/2 x 5-1/2 inches) 2. Washers 4. Chains 3.
PAGE 4