Installation Instructions

ManualsBrandsToro ManualsVehiclesFront Light Replacement Kit, Workman Utility Vehicle

FormNo.3429-224RevA

FrontLightReplacementKit

Workman

UtilityVehicle

ModelNo.139-4500

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Prepareamachine.

Light1

Bracket1

Replaceafrontlight(forGTXand2016andafterMDX

modelswithoutaBrushGuardKitinstalled).

Light1

Bracket1

Replaceafrontlight(forGTXand2016andafterMDX

modelswithaBrushGuardKitinstalled).

Light1

Bracket1

Replaceafrontlight(for2016andbeforeMDXmodels).

Light1

Leftbracket

Rightbracket1

Replaceafrontlight(forHD,HDX,HDX-D,andHDX-Auto

models).

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Checkthefunctionofthesignallights.

PreparingaMachine

1.Parkamachineonalevelsurface.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

4.ForElectricGTXModels:disconnectthemain

negativebatterycable(black)thatconnects

thebankofbatteriestothegroundpointofthe

machine;refertoyourOperator’sManual.

5.ForallotherWorkmanModels:disconnectthe

negativebatterycable;refertoyourOperator’s

Manual.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3429-224*A

Summary of content (4 pages)

PAGE 1
Form No. 3429-224 Rev A Front Light Replacement Kit Workman® Utility Vehicle Model No. 139-4500 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. No parts required – Prepare a machine. Light Bracket Light Bracket Light Bracket Light Left bracket Right bracket 1 1 1 1 1 1 1 1 1 Replace a front light (for GTX and 2016 and after MDX models without a Brush Guard Kit installed).
PAGE 2
Replacing a Front Light 4. For GTX and 2016 and After MDX Models Without a Brush Guard Kit Installed 1. Connect the wire harness lead to the front position/signal light. Replacing a Front Light For GTX and 2016 and After MDX Models With a Brush Guard Kit Installed Remove the 2 existing screws from the headlight bracket (Figure 1). Retain the fasteners. 1. Remove the existing front position/signal light. Retain the fasteners. 2.
PAGE 3
Replacing a Front Light Replacing a Front Light For 2016 and Before MDX Models For HD, HDX, HDX-D, and HDX-Auto Models 1. Remove the existing front position/signal light. 1. Retain the fasteners. 2. Remove the existing front position/signal light. Retain the fasteners. Secure the light to the bracket using the previously removed fasteners (Figure 4). 2.
PAGE 4
Connecting the Battery For Electric GTX Models: Connect the main negative battery cable (black) that connects the bank of batteries to the ground point of the machine; refer to your Operator’s Manual. For all other Workman Models: connect the negative battery cable; refer to your Operator’s Manual. Checking the Function of the Signal Lights Push the signal-controller lever down to engage the left signal lights. g026655 Figure 6 1. Position light (amber lens outward) 4. Hole 2. Lamp bracket 5.