Installation Instructions

ManualsBrandsToro ManualsWalk-Behind MowersLight Kit, Proline Commercial Walk-Behind Mower with 60in Floating Cutting Unit

FormNo.3436-365RevA

LightKit

ProlineCommercialWalk-BehindMowerwith60inFloatingCutting

Unit

ModelNo.139-5595

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

LEDlight2

Lightbracket1

Frictionwasher2

Carriagebolt(5/16x7/8inch)

Flangenut(5/16inch)

Lightclamp2

Locknut(1/4inch)

Installthelights.

Wireharness1

Cableties

Toggleswitch1

Routethewireharness.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,disengage

thePTO,andengagetheparkingbrake.

2.Shutofftheengine,removethekey,andwait

forallmovingpartstostopbeforeleavingthe

operatingposition.

3.Disconnectthebattery;refertoyourOperator’s

Manual.

InstallingtheLights

Partsneededforthisprocedure:

2LEDlight

1Lightbracket

2Frictionwasher

Carriagebolt(5/16x7/8inch)

Flangenut(5/16inch)

2Lightclamp

Locknut(1/4inch)

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-365*A

Summary of content (8 pages)

PAGE 1
Form No. 3436-365 Rev A Light Kit Proline Commercial Walk-Behind Mower with 60in Floating Cutting Unit Model No. 139-5595 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Procedure 1. 2. Secure the 2 LED lights to the light bracket using 2 carriage bolts (5/16 x 7/8 inch), 2 friction washers, and 2 flange nuts (5/16 inch) as shown in Figure 1. Secure the light assembly to the muffler guard using 2 light clamps and 4 locknuts (1/4 inch) as shown in Figure 2. g307081 Figure 2 g307082 Figure 1 1. Carriage bolt (5/16 x 7/8 inch) 4. Light bracket 2. LED light 5. Flange nut (5/16 inch) 3. Friction washer 2 1. Light clamp 3. Light assembly 2. Locknut (1/4 inch) 4.
PAGE 3
2. 3 Secure the wire harness to the light bracket using the 2 push-mount fasteners on the wire harness (Figure 4). Routing the Wire Harness Parts needed for this procedure: 1 Wire harness 6 Cable ties 1 Toggle switch Procedure 1. Plug the 2 connectors at the front of the machine into the LED lights (Figure 3). g307415 Figure 4 1. Push-mount fastener g307414 Figure 3 1. Light connector 2. Harness connector 3 2.
PAGE 4
3. Route the wire harness along the right side of the machine as shown in Figure 5. 4. Secure the wire harness to the machine using the cable ties (Figure 5).
PAGE 5
. Plug the connector into the toggle-switch connector (Figure 6). 7. From the top of the threads on the toggle switch, set the depth of the bottom hex nut at 7.9 mm (5/16 inch) as shown in Figure 8. g307412 Figure 6 1. Harness connector 6. 2. Toggle-switch connector Drill a hole (12 mm or 1/2 inch) in front of the hour meter for the toggle switch (Figure 7). g307440 Figure 8 1. 7.9 mm (5/16 inch) g307413 Figure 7 1. Measure 12.7 mm (1/2 inch) from the hour meter to drill the hole. 2.
PAGE 6
8. Secure the toggle switch in the opening using the 2 hex nuts and 1 lock washer (Figure 9). 9. Note: Do not use the key-tab washer. g307441 Figure 9 1. Hex nut 3. Toggle switch 2. Lock washer 6 Connect the battery; refer to your Operator’s Manual.
PAGE 7
Notes:
PAGE 8