Installation Instructions

ManualsBrandsToro ManualsWalk-Behind MowersSoft Side Bagger, ProLine Commercial Walk-Behind Mower

FormNo.3438-297RevB

SoftSideBagger

ProLineCommercialWalk-BehindMower

ModelNo.139-7860

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal114-3489

114-3489

1.Thrownobjecthazard;cutting/dismembermenthazard—do

notoperatethemachinewiththedischargeopening

uncovered;alwaysoperatethemachinewiththerear

dischargedeector,dischargecover,orgrasscollector

installed.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3438-297*B

Summary of content (12 pages)

PAGE 1
Form No. 3438-297 Rev B Soft Side Bagger ProLine Commercial Walk-Behind Mower Model No. 139-7860 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal114-3489 114-3489 1.
PAGE 2
Installation Note: Determine the left and right sides of the machine from the normal operating position. 1 Preparing the Machine g314767 No Parts Required Figure 1 Procedure 1. Park the machine on a level surface. 2. Disengage the PTO and engage the parking brake. 3. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 1. Back plate 3. Support 2. Locknuts (1/4 inch) 4. Bolts (1/4 x 5/8 inch) 2.
PAGE 3
Assembling the Bag and Frame Parts needed for this procedure: 1 Bag and pan 1 Catcher frame 2 Handle 4 Bolt (1/4 x 1 inch) 4 Locknut (1/4 inch) 4 Washer (1/4 inch) g314783 Figure 3 1. Locknut (3/8 inch) 3. Bolt (3/8 x 3/4 inch) 2. Clamp 4. Install the latches to both sides of the back plate using 4 phillips-head screws, 4 lock washers, and 4 locknuts (#10); Figure 4. Procedure Important: Do not completely tighten the 1.
PAGE 4
g315748 Figure 7 1. Rounded-edge-discharge baffle 1. g002159 3. Washer (1/4 inch) 2. Bolt (1/4 x 1 inch) 4. Locknut (1/4 inch) Remove the 2 bolts and 2 nuts securing the existing discharge baffle to the deck and remove the discharge baffle (Figure 8). Note: Retain the baffle and corresponding hardware for converting back to side discharge. Figure 6 1. Handle 2.
PAGE 5
2. For 36-inch and 60-inch decks: Install the square-edge-discharge baffle with appropriate hardware as shown in Figure 9. 3. For 48-inch and 54-inch decks: Install the rounded-edge-discharge baffle and bagger guard with appropriate hardware as shown in Figure 10. g314841 Figure 9 1. For 36-inch decks: Bolt 4. Square-edge-discharge (5/16 x 1 inch); for 60-inch baffle decks: Carriage bolt 2. For 36-inch decks: Bolt (3/8 x 1 inch); for 60-inch decks: Button-head bolt g317000 Figure 10 5.
PAGE 6
WARNING 5 An uncovered discharge opening could allow the machine to throw objects at you or bystanders and result in serious injury. Also, contact with the blade could occur. Removing the Deflector No Parts Required Never operate the machine unless you install a mulch plate, discharge deflector, or grass collection system. Procedure 1. 6 Remove the cotter pin (Figure 11). Retain the pin for use in Step 4 in 6 Installing the Bagger onto the Machine (page 6). 2.
PAGE 7
Product Overview Note: Do not remove or install the clamp to remove or install the back plate when using the bagger on a machine of the same size. Lift the back plate off of the machine. 6. Insert the lower pins of the bagger frame into the holes on the back plate (Figure 13). 7. Lift the latches and slide the frame side pins into them (Figure 13). 8. Lower the latches to secure the bagger. g315746 Figure 14 1. Bagger Specifications g002161 Figure 13 1. Back plate holes 3. Latch 2.
PAGE 8
Operation 2. General Safety Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Lift the latches and remove and empty the grass bag. 4. Use a stick or similar object, not your hands to remove and clear the obstruction from the machine. 5. Insert the lower pins of the bagger frame into the holes in the back plate (Figure 13). 6. Lift the latches and slide the frame side pins into them (Figure 13). 7.
PAGE 9
Maintenance Inspecting the Bagger Service Interval: After the first 10 hours Before storage 1. Inspect all the fasteners and latches; replace any that are missing or damaged. 2. Inspect the bag for damage and replace any damaged parts. 3. Tighten all hardware. WARNING You or bystanders could be severely injured by flying debris or thrown objects that may pass through torn, worn, or deteriorated grass bags. • Check the grass bags for holes, rips, wear, and other deterioration.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12