Installation Instructions

ManualsBrandsToro ManualsWalk-Behind MowersSoft Side Bagger, ProLine Commercial Walk-Behind Mower

FormNo.3438-309RevB

SoftSideBagger

ProLineCommercialWalk-BehindMower

Номермодели139-7860

Инструкциипомонтажу

Техника

безопасности

Наклейкисправиламитехникибезопасностии

инструкциями

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal114-3489

114-3489

1.Thrownobjecthazard;cutting/dismembermenthazard—do

notoperatethemachinewiththedischargeopening

uncovered;alwaysoperatethemachinewiththerear

dischargedeector,dischargecover,orgrasscollector

installed.

8111LyndaleAvenueSouth

Bloomington,MN55420

Регистрациявwww.T oro.com.

Переводисходногодокумента(RU)

PrintedintheUSA

Всеправазащищены

*3438-309*B

Summary of content (12 pages)

PAGE 1
Form No. 3438-309 Rev B Soft Side Bagger ProLine Commercial Walk-Behind Mower Номер модели 139-7860 Инструкции по монтажу Техника безопасности Наклейки с правилами техники безопасности и инструкциями Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal114-3489 114-3489 1.
PAGE 2
Монтаж Примечание: Determine the left and right sides of the machine from the normal operating position. 1 Preparing the Machine g314767 Детали не требуются Рисунок 1 Процедура 1. Park the machine on a level surface. 2. Disengage the PTO and engage the parking brake. 3. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 1. Back plate 3. Support 2. Locknuts (1/4 inch) 4. Bolts (1/4 x 5/8 inch) 2.
PAGE 3
Assembling the Bag and Frame Детали, требуемые для этой процедуры: 1 Bag and pan 1 Catcher frame 2 Handle 4 Bolt (1/4 x 1 inch) 4 Locknut (1/4 inch) 4 Washer (1/4 inch) g314783 Рисунок 3 1. Locknut (3/8 inch) 3. Bolt (3/8 x 3/4 inch) 2. Clamp 4. Install the latches to both sides of the back plate using 4 phillips-head screws, 4 lock washers, and 4 locknuts (#10); Рисунок 4. Процедура Внимание: Do not completely tighten the 1.
PAGE 4
g315748 Рисунок 7 1. Rounded-edge-discharge baffle 1. g002159 3. Washer (1/4 inch) 2. Bolt (1/4 x 1 inch) 4. Locknut (1/4 inch) Remove the 2 bolts and 2 nuts securing the existing discharge baffle to the deck and remove the discharge baffle (Рисунок 8). Примечание: Retain the baffle and Рисунок 6 1. Handle 2. Square-edge-discharge baffle corresponding hardware for converting back to side discharge.
PAGE 5
2. For 36-inch and 60-inch decks: Install the square-edge-discharge baffle with appropriate hardware as shown in Рисунок 9. 3. For 48-inch and 54-inch decks: Install the rounded-edge-discharge baffle and bagger guard with appropriate hardware as shown in Рисунок 10. g314841 Рисунок 9 1. For 36-inch decks: Bolt 4. Square-edge-discharge (5/16 x 1 inch); for 60-inch baffle decks: Carriage bolt 2. For 36-inch decks: Bolt (3/8 x 1 inch); for 60-inch decks: Button-head bolt g317000 Рисунок 10 5.
PAGE 6
ПРЕДУПРЕЖДЕНИЕ 5 An uncovered discharge opening could allow the machine to throw objects at you or bystanders and result in serious injury. Also, contact with the blade could occur. Removing the Deflector Детали не требуются Never operate the machine unless you install a mulch plate, discharge deflector, or grass collection system. Процедура 1. 6 Remove the cotter pin (Рисунок 11). Retain the pin for use in Step 4 in 6 Installing the Bagger onto the Machine (страница 6). 2.
PAGE 7
Знакомство с изделием Примечание: Do not remove or install the clamp to remove or install the back plate when using the bagger on a machine of the same size. Lift the back plate off of the machine. 6. Insert the lower pins of the bagger frame into the holes on the back plate (Рисунок 13). 7. Lift the latches and slide the frame side pins into them (Рисунок 13). 8. Lower the latches to secure the bagger. g315746 Рисунок 14 1. Bagger g002161 Рисунок 13 1. Back plate holes 3. Latch 2. Frame pin 4.
PAGE 8
Эксплуатация 2. General Safety Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Lift the latches and remove and empty the grass bag. 4. Use a stick or similar object, not your hands to remove and clear the obstruction from the machine. 5. Insert the lower pins of the bagger frame into the holes in the back plate (Рисунок 13). 6. Lift the latches and slide the frame side pins into them (Рисунок 13). 7.
PAGE 9
Техническое обслуживание bagger. If you must store it outside, cover it with a weatherproof cover. Inspecting the Bagger Интервал обслуживания: Через первые 10 часа Перед помещением на хранение 1. Inspect all the fasteners and latches; replace any that are missing or damaged. 2. Inspect the bag for damage and replace any damaged parts. 3. Tighten all hardware.
PAGE 10
Примечания:
PAGE 11
Примечания:
PAGE 12