Installation Instructions

ManualsBrandsToro ManualsRiding ProductsJumper Kit, Greensmaster 3360 or 3370 eTriFlex Traction Unit with 3WD

FormNo.3443-968RevA

JumperKit

Greensmaster

3360or3370eTriFlexTractionUnitwith

Three-Wheel-DriveKit

ModelNo.139-8599

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Harnessbracket1

Clipconnector

Installingtheharnessbracket.

Wireharness1

Cabletie

Connectthekitwireharnesstothe

machinewireharnessandthegearbox

motor.

Nopartsrequired

–

Engage3-wheel-drivemode.

Nopartsrequired

–

Completetheinstallation.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowerthecuttingunits.

4.Shutoffthemachineandremovethekey.

5.Disconnectthemain-powerconnectors;referto

yourmachineOperator’sManual.

InstallingtheHarness

Bracket

Partsneededforthisprocedure:

1Harnessbracket

Clipconnector

RemovingtheExistingHarness

Bracket

1.Disconnectthemachine-wire-harness

connectorsfromthemotorconnectors(Figure

1).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3443-968*

Summary of content (4 pages)

PAGE 1
Form No. 3443-968 Rev A Jumper Kit Greensmaster® 3360 or 3370 eTriFlex Traction Unit with Three-Wheel-Drive Kit Model No. 139-8599 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description No parts required – Harness bracket Clip connector Wire harness 1 1 1 Cable tie 1 Connect the kit wire harness to the machine wire harness and the gearbox motor. No parts required – Engage 3-wheel-drive mode.
PAGE 2
Installing the New Harness Bracket 1. Secure the clip connector to the harness bracket (Figure 3). g344247 Figure 3 1. Harness bracket 2. g301663 Figure 1 1. Machine-wire-harness connectors 2. 2. Clip connector Use the previously removed hardware to secure the new harness bracket to the caster fork (Figure 4). 2. Motor connectors Remove the hardware that secures the harness bracket to the caster fork (Figure 2). Retain the hardware. g344250 Figure 4 1. Flange nut 4. Washer 2. Spacer 5.
PAGE 3
3. Raise the hood. 4. Route the remaining kit-wire-harness connectors towards the steering motor (Figure 6) Connecting the Kit Wire Harness Parts needed for this procedure: 1 Wire harness 1 Cable tie Procedure g344561 Figure 6 1. Steering column 5. Kit wire harness 2. Machine wire harness 3. 4-socket connector (machine wire harness) 6. Push-mount fastener 7. 2-socket connector (machine wire harness) 4. 4-pin connector (kit wire harness) 8. 2-pin connector (kit wire harness) 5.
PAGE 4
Engaging 3-Wheel-Drive Mode No Parts Required Procedure 3-wheel-drive mode should automatically enable when you install the gearbox-wire-harness connections to the machine wire harness. To ensure that 3-wheel-drive mode is activated, navigate to the 3WD KIT option in the SETTINGS menu of your InfoCenter. The item selected/active icon indicates that 3-wheel-drive mode is activated.