Installation Instructions

ManualsBrandsToro ManualsRiding ProductsCarbon Canister Kit, Multi Pro 5800 Turf Sprayer

FormNo.3434-852RevA

CarbonCanisterKit

MultiPro

5800TurfSprayer

ModelNo.140-0550

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Canisterbracket

Grommet(9/16inch)

Carboncanister

Canisterclamp

Bushing1

Elbowtting

Hose(10-1/2inches)

Straighttting(3/16to1/4inch)

Hose(25inches)

Hoseclamp(13/32inch)

Hoseclamp(1/2inch)

Connectthecanistertothefueltank.

Valvebracket1

Grommet(1/2inch)

Vacuum-controlvalve1

Hose(10-1/2inches)

Straighttting(3/16to1/4inch)

Straighttting(1/4to5/16inch)

Hose(9inches)

Hoseclamp(13/32inch)

Hoseclamp(1/2inch)

Cabletie

Connectthevacuum-controlvalveand

valvebracket.

Hose(10-1/2inches)

Hose(9-1/2inches)

T-tting(1/2x1/2x5/16inch)

T-tting(1/4x1/4x1/4inch)

Hoseclamp(1/2inch)

Hoseclamp(5/16inch)

Hoseclamp(13/16inch)

Fuelcap1

Completetheinstallation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3434-852*A

Summary of content (8 pages)

PAGE 1
Form No. 3434-852 Rev A Carbon Canister Kit Multi Pro® 5800 Turf Sprayer Model No. 140-0550 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 © 2019—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
6. 1 Under the cover, place the bushing as shown in Figure 2 and mark the center on the fuel tank. Preparing the Machine No Parts Required Procedure Note: Retain all removed parts for later installation unless otherwise noted. 1. 2. Park the machine on a level surface, shift the transmission into the NEUTRAL position (manual) or the PARK position (automatic) and engage the parking brake. g302389 Figure 2 1. Place the bushing here and mark the center.
PAGE 3
5. 2 Install the canister bracket assembly with the screws removed in 1 Preparing the Machine (page 2) Connecting the Canister to the Fuel Tank Parts needed for this procedure: 1 Canister bracket 2 Grommet (9/16 inch) 1 Carbon canister 1 Canister clamp 1 Bushing 1 Elbow fitting 1 Hose (10-1/2 inches) 1 Straight fitting (3/16 to 1/4 inch) 1 Hose (25 inches) 2 Hose clamp (13/32 inch) 2 Hose clamp (1/2 inch) g302502 Figure 3 Procedure 1.
PAGE 4
5. 3 Connect the loose end of the upper hose on the vacuum-control valve to the small end of the straight fitting (1/4 to 5/16 inch) and secure it with a hose clamp (1/2 inch).
PAGE 5
6. Route the 9 inch hose through the 1-hole tab on the valve bracket to the remaining inlet on the vacuum-control valve. 7. Secure the 9 inch hose to the vacuum-control valve with a hose clamp (13/32). 8. Connect the loose end of the 9 inch hose to the small end of a straight fitting (3/16 to 1/4 inch) with a hose clamp (13/32 inch). 9.
PAGE 6
4. 7. Connect the loose end of the 9-1/2 inch hose to the center branch of the 1/2 x 1/2 x 5/16 inch T-fitting and secure it with a hose clamp (5/16 inch). Position the 1/2 x 1/2 x 5/16 inch T-fitting along the long vacuum hose extending from the top of the engine and cut the hose where appropriate to install the T-fitting. Note: Cut the PCV hose about 10-1/2 inches away from itsconnection to the engine. 8.
PAGE 7
Notes:
PAGE 8