Installation Instructions

ManualsBrandsToro ManualsRiding ProductsPower Harness Kit, Groundsmaster 3200 or 3300 Series Traction Unit

FormNo.3441-987RevA

PowerHarnessKit

Groundsmaster

3200or3300SeriesTractionUnit

ModelNo.140-1559

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Disconnectthebattery.

Powerharness1

Cabletie

Relay1

Fuse(10A)

Routethepowerharness.

Nopartsrequired

–

Connectthebattery.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowertheattachments.

4.Shutofftheengineandremovethekey.

DisconnectingtheBattery

NoPartsRequired

RemovingtheBatteryCables

WARNING

Batteryterminalsormetaltoolscouldshort

againstmetalcomponents,causingsparks.

•Whenremovingorinstallingthebattery,

donotallowthebatteryterminalstotouch

anymetalpartsofthemachine.

•Donotallowmetaltoolstoshortbetween

thebatteryterminalsandmetalpartsofthe

machine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3441-987*

Summary of content (8 pages)

PAGE 1
Form No. 3441-987 Rev A Power Harness Kit Groundsmaster® 3200 or 3300 Series Traction Unit Model No. 140-1559 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Use Qty. No parts required – Prepare the machine. No parts required – Disconnect the battery. 3 Power harness Cable tie Relay Fuse (10 A) 1 6 1 1 Route the power harness. 4 No parts required – Connect the battery.
PAGE 2
WARNING 3 Electrical sparks can cause the battery gasses to explode, resulting in personal injury. Incorrect battery cable routing could damage the machine and cables, causing sparks. Routing the Power Harness • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. Parts needed for this procedure: • Always connect the positive (red) battery cable before connecting the negative (black) cable. 1.
PAGE 3
g310730 Figure 2 1. Ring terminals 3. Relay 5. Main harness connector 2. Cable tie 4. Optional control pod connector 6. Accessory power connections 4. Route the harness to the connector positions shown in Figure 2. 5. Secure the harness to the machine with the cable ties shown in Figure 2. 6. Rotate the latches and remove the side cover on the armrest (Figure 3). 3 7.
PAGE 4
Connecting the Battery No Parts Required Procedure WARNING Electrical sparks can cause the battery gasses to explode, resulting in personal injury. Incorrect battery cable routing could damage the machine and cables, causing sparks. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. g333069 • Always connect the positive (red) battery cable before connecting the negative (black) cable. Figure 3 1. Cover 7.
PAGE 5
g252786 Figure 5 1. Positive battery cable 2. Negative battery cable 2. Connect the negative cable to the battery and tighten the battery-clamp nut (Figure 5). 3. Assemble the insulator over the positive battery terminal (Figure 5).
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8