Installation Instructions

ManualsBrandsToro ManualsWalk-Behind MowersRecycler Kit, Proline Commercial Walk-Behind Mower with 48in Floating Cutting Unit

FormNo.3436-332RevA

48in,54in,or60inRecycler

Kit

ProlineCommercialWalk-BehindMowerwithFloatingCuttingUnit

ModelNo.140-1914

ModelNo.140-1915

ModelNo.140-1916

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Rightbafe

Carriagebolt(5/16x3/4inch)—48-inch

decksonly

Carriagebolt(5/16x3/4inch)—54-inch

decksonly

Nut(5/16inch)—48-inchand60-inch

decksonly

Nut(5/16inch)—54-inchdecksonly

Installtherightbafe.

Dischargechutecover1

Bolt(3/8x1inch)—48-inchdecksonly

Bolt(3/8x1inch)—54-inchand60-inch

decksonly

Nut(3/8inch)—48-inchand54-inch

decksonly

Nut(3/8inch)—60-inchdecksonly

Nut(5/16inch)—60-indecksonly

Bolt(3/8x1-1/4inches)—54-inchdecks

only

Bolt(5/16x1-1/4inches)—60-inch

decksonly

Installthedischargechutecover.

Kickerbafe

Hex-washer-headbolt(5/16x3/4inch)

Installthekickerbafes(48-inchdecks

only).

Leftbafe

Carriagebolt(5/16x3/4inch)—48-inch,

54-inch,and60-inchdecks

Nut(5/16inch)—48-inchdecksonly

Nut(5/16inch)—54-inchand60-inch

decksonly

Installtheleftbafe.

Decal1

Mulchingblades3

Installthedecalandmulchingblades.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-332*A

Summary of content (8 pages)

PAGE 1
Form No. 3436-332 Rev A 48in, 54in, or 60in Recycler® Kit Proline Commercial Walk-Behind Mower with Floating Cutting Unit Model No. 140-1914 Model No. 140-1915 Model No. 140-1916 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 3 4 5 6 7 © 2019—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Disengage the PTO, engage the parking brake. 3. Shut off the engine and remove the key. 4. For easier access, raise the front of the machine and support it using jack stands rated for your machines. g209902 Figure 1 54-inch deck shown 1. Nut 2. Cutoff baffle 3. Bolt WARNING 3. Mechanical or hydraulic jacks may fail to support the machine and cause serious injury.
PAGE 3
54-Inch Decks 48-Inch Decks 1. 1. Install the right baffle using 2 nuts (5/16 inch) as shown in Figure 2. Tighten the fasteners by hand. Remove the nuts and bolts from the location shown in Figure 4. g308772 Figure 4 1. Nuts and bolts g012805 Figure 2 2. 3. Welded posts 1. Nut (5/16 inch) 2. Right baffle 2. Install the right baffle using 1 carriage bolt (5/16 x 3/4 inch) and 3 nuts (5/16 inch) as shown in Figure 5. Tighten the fasteners by hand.
PAGE 4
g308757 Figure 6 1. Nut (5/16 inch) 4. 2. Carriage bolt (5/16 x 3/4 inch) Tighten all fasteners. g219326 Figure 8 1. Nut—5/16 inch (3) 60-Inch Decks 1. 3. Welded post (3) 2. Right baffle Remove the nut and bolt from the location shown in Figure 7 or Figure 8. 3. Tighten the fasteners by hand. 4 Installing the Discharge Chute Cover Parts needed for this procedure: g219304 Figure 7 1. Nut and bolt 2. Install the right baffle using 3 nuts (5/16 inch) as shown in Figure 8.
PAGE 5
Procedure 54-inch Decks 48-inch Decks Install the discharge chute cover using 1 bolt (3/8 x 1-1/4 inches), 2 bolts (3/8 x 1 inch) and 3 nuts (3/8 inch) as shown in Figure 11. Install the discharge chute cover using 3 bolts (3/8 x 1 inch) and 3 nuts (3/8 inch) as shown in Figure 9 and Figure 10. g307460 Figure 11 g308754 Figure 9 1. Bolts (3/8 x 1 inch) 1. Bolt (3/8 x 1-1/4 inches) 3. Nuts (3/8 inch) 3. Bolts (3/8 x 1 inch) 2. Nuts (3/8 inch) 2.
PAGE 6
5 6 Installing the Kicker Baffles Installing the Left Baffle 48-Inch Decks Only Parts needed for this procedure: 1 Left baffle 1 Carriage bolt (5/16 x 3/4 inch)—48-inch, 54-inch, and 60-inch decks 3 Nut (5/16 inch)—48-inch decks only 4 Nut (5/16 inch)—54-inch and 60-inch decks only Parts needed for this procedure: 2 Kicker baffle 4 Hex-washer-head bolt (5/16 x 3/4 inch) Procedure Procedure Install the kicker baffles to the underside of the deck using 4 bolts (5/16 x 3/4 inch) at the locatio
PAGE 7
g219327 Figure 15 1. Nut (5/16 inch) 3. Left baffle 2. Carriage bolt (5/16 x 3/4 inch) 4. Remove the existing hardware from these holes (54-inch decks only) g209974 Figure 16 1. 30 mm (1.19 inches) 2. Tighten all fasteners. 2. 7 Installing the Decal and Mulching Blades Parts needed for this procedure: 1 Decal 3 Mulching blades Procedure 1. Install the decal to the mower deck in the location shown in Figure 16. 7 2. 17 mm (0.
PAGE 8
Stopping the Machine Operation If you must stop the forward motion of the machine while mowing, a clump of grass clippings may drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or you can disengage the mower deck while moving forward. Operating Tips Using the Fast Throttle Setting For best mowing and maximum air circulation, operate the engine at the FAST position.