Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSunshade Kit, TimeCutter Riding Mower

FormNo.3436-462RevB

SunshadeKit

forTimeCutter

RidingMowers

ModelNo.140-2054

InstallationInstructions

1.Parkthemachineonalevelsurface,disengage

theblade-controlswitch,andmovethe

motion-controlleversoutwardtothePARK

position.

2.Shutofftheengine,removethekey,andwait

forallmovingpartstostopbeforeleavingthe

operatingposition.

3.Supporttherearofthemachinewithjackstands

andremovethereartires.

4.Securethereceiverbracketstothefront2holes

intheframeusing2bolts(1/2inchx1-1/8

inch)andsplitlockwashers(Figure1).Ifyour

machineisnotequippedwithaROPS,insertthe

spacerplateasshowninFigure1.

Important:Ensurethatyoudonotpinch

anycablesorfuellineswheninstallingthe

receiverbracket.

g309688

Figure1

1.Bolt(1/2inchx1-1/8inch)4.Spacerplate(optional)

2.Splitlockwasher(1/2inch)

5.Receiverbracket

3.Frame

5.Looselysecuretheouterholesofthefrontbow

tothesecondholesoftherearbowusing2bolts

(1/4x5/8inch)andlocknuts(Figure2).

Note:Ensurethattheendsofthefrontboware

ontheoutsideoftherearbow.

g309689

Figure2

1.Bolt(1/4x5/8inch)

4.Topbow

2.Locknut5.Frontbow

3.Rearbow

6.Looselysecurethetopbowtothefrontandrear

bowusing2bolts(1/4x5/8inch)andlocknuts

(Figure2).

7.Anglethetopbowapproximately10cm(4

inches)forwardofverticalandtightenthe

fasteners.

8.Looselysecurethebracestothepostsusing2

bolts(1/4x1-1/4inches),washers,andlocknuts

(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-462*B

Summary of content (2 pages)

PAGE 1
Form No. 3436-462 Rev B Sunshade Kit for TimeCutter® Riding Mowers Model No. 140-2054 Installation Instructions 1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the PARK position. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Support the rear of the machine with jack stands and remove the rear tires. 4.
PAGE 2
g309691 Figure 4 1. Rear screen 14. g309690 Figure 3 1. Bolt (1/4 x 5/8 inch) 6. Bolt (1/4 x 1-1/4 inches) 2. Locknut (1/4 inch) 7. Locknut (1/4 inch) 3. Bolt 1/4 x 5/8 inch and locknut (1/4 inch) 8. Bolt (1/4 x 1 inch) 4. Brace 5. Washer (1/4 inch) 9. Post 9. 10. 11. Slip the sunshade over the front bow and pull it back over the rear bow (Figure 5). Angle the top bow up or down to tighten or loosen the sunshade.