Installation Instructions

ManualsBrandsToro ManualsRiding ProductsDeluxe Seat Kit, TimeCutter Riding Mower

FormNo.3436-798RevB

DeluxeSeatKit

TimeCutter

RidingMower

ModelNo.140-2057

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheexistingseat.

Seatback

Bolt(5/16x1–1/2inches)

Nut(5/16inch)

Seat-baseassembly

Installthedeluxeseatkit.

Nopartsrequired

–

Testthesafety-interlocksystem.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Disengagetheblade-controlswitch.

3.Movethemotion-controlleversoutwardtothe

NEUTRAL-LOCKpositiontoengagetheparking

brake.

4.Shutofftheengineandremovethekey.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3436-798*B

Summary of content (4 pages)

PAGE 1
Form No. 3436-798 Rev B Deluxe Seat Kit TimeCutter® Riding Mower Model No. 140-2057 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the existing seat. 3 Seat back Bolt (5/16 x 1–1/2 inches) Nut (5/16 inch) Seat-base assembly 1 2 2 1 Install the deluxe seat kit. 4 No parts required – Test the safety-interlock system.
PAGE 2
4. Tilt the seat down. 5. Remove the 2 bolts holding the existing seat assembly on the pivot rod (Figure 3). Note: Retain the 2 bolts for installation of the deluxe seat assembly. Removing the Existing Seat Assembly No Parts Required Procedure 1. 2. Tilt the seat up as shown in Figure 1. Unhook the tilt cable from the seat pan (Figure 1). g308596 Figure 3 6. Remove the seat assembly from the machine (Figure 4). g313311 Figure 1 1. Tilt cable 3.
PAGE 3
Installing the Deluxe Seat Kit Parts needed for this procedure: 1 Seat back 2 Bolt (5/16 x 1–1/2 inches) 2 Nut (5/16 inch) 1 Seat-base assembly g298473 Figure 6 Procedure 1. 1. Seat back Secure the seat-base assembly onto the pivot rod with the 2 bolts previously removed (Figure 5). 2. Bolts and nuts 4. Tilt the seat assembly up. 5. Connect the seat switch (Figure 7). g308749 Figure 7 g308748 Figure 5 2. Slide the seat back onto the seat-base posts and align the holes (Figure 6). 3.
PAGE 4
Product Overview Controls Fore/Aft Adjustment Lever The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable (Figure 9). g313032 Figure 8 1. Seat-tilt cable 4 Testing the Safety-Interlock System g027632 Figure 9 No Parts Required Procedure CAUTION If safety interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. • Do not tamper with the interlock switches.