Form No. 3436-785 Rev B Deck Footlift Assist Kit TimeCutter® Riding Mower Model No. 140-2059 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the MyRide guard. No parts required – Remove the lift lever.
1 2 Preparing the Machine Removing the MyRide Guard No Parts Required No Parts Required Procedure 1. Park the machine on a level surface. Procedure 2. Disengage the blade-control switch (PTO), move the motion-control levers to the NEUTRAL-LOCK position, and engage the parking brake. Note: This procedure is only for machines with the 3. 4. MyRide option. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 1.
Removing the Lift Lever No Parts Required Procedure Remove the hex-head bolt (5/16 x 1 inch) and flange nut (5/16 inch) securing the lift lever (Figure 2). Retain the lift lever for later installation. You can discard the hex-head bolt (5/16 x 1 inch) and flange nut (5/16 inch). g343672 Figure 2 1. Hex-head bolt (5/16 x 1 inch) 3. Flange nut (5/16 inch) 2.
Installing the Foot Pedal Parts needed for this procedure: 1 Lift pedal 1 Foot peg 1 Foot-lift plate 2 Carriage bolt (5/16 x 1-1/4 inches) 2 Locknut (5/16 inch) 2 Thrust washer 1 Spacer (3/8 inch) 2 Spacer (5/16 inch) 1 Link 1 Carriage bolt (3/8 x 1 inch) 2 Locknut (5/16 inch) 2 Shoulder bolt (3/8 x 7/8 inch) 3 Locknut (3/8 inch) 1 Hex-head bolt (3/8 x 1 inch) 1 Washer 1 Nylon washer 1 Anti-seize packet 4
Procedure 1. Secure the foot peg to the lift pedal using 1 hex-head bolt (3/8 x 1 inch) as shown in Figure 3. 2. Secure the lift pedal to the link using 1 shoulder bolt (3/8 x 7/8 inch) and 1 locknut (3/8 inch) as shown in Figure 3. 3. Secure the lift pedal to the side of the frame using 1 shoulder bolt (3/8 x 7/8 inch), 1 nylon washer, 1 washer, and 1 locknut (3/8 inch) as shown in Figure 3. g343722 Figure 3 1. Hex-head bolt (3/8 x 1 inch) 5. Locknut (3/8 inch) 2. Foot peg 6.
4. Apply anti-seize to both sides of the 2 thrust washers. 5. Install the thrust washers on each side of the lift lever (Figure 4). Note: Install all the carriage bolts with the bolt heads on the inside of the machine. 6. Secure the foot-lift plate to the link using 1 carriage bolt (3/8 x 1 inch), 2 carriage bolts (5/16 x 1-1/4 inches), 1 spacer (3/8 inch), 2 spacers (5/16 inch), 1 locknut (3/8 inch), and 2 locknuts (5/16 inch) as shown in Figure 4. g343743 Figure 4 1. Locknut (3/8 inch) 6.
5 Completing the Setup No Parts Required Procedure 1. For machines with the MyRide Suspension System, slide the guard tab into the frame (Figure 1). 2. For machines with the MyRide Suspension System, install the bolts into the frame and guard (Figure 1). 3. Use the height-of-cut lever and foot pedal to raise and lower the mower deck, check to see if there is any binding. If so, check the installation. 4. Adjust as necessary.