Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSound Reducing Kit, Groundsmaster 3200 or 3300 Series Traction Unit with Winter Enclosure

FormNo.3445-275RevA

SoundReducingKit

Groundsmaster

3200or3300SeriesTractionUnitwithWinter

Enclosure

ModelNo.140-6721

InstallationInstructions

Installation

TheSoundReducingKitcanbeinstalledonthe

following:

•Tractionunits(Models31903and31909)

•Winterenclosure(Model31990)

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface.

2.Engagetheparkingbrake.

3.Lowertheattachment.

4.Shutofftheengineandremovethekey.

5.Disconnectthebattery;refertotheelectrical

systemmaintenancesectioninyourOperator’s

Manual.

InstallingtheFloor

Components

Partsneededforthisprocedure:

Steeringplug

1Uppersteeringplug

1Lowersteeringplug

Steeringpad

3Mounting-tabplug

Corneroorpad

Centeroorpad

Brakeplug—7.6cm(3inches)width

Brakeplug—3.1cm(1.22inch)width

ROPSplug

Seat-basepad(thin)

Seat-basepad(thick)

Seatpad

1Rear-windowpad

Lower-rewallpad

Upper-rewallpad

1Firewalltilepad

Upperbrakefoam

Lowerbrakefoam

1Rightcornerpad

Leftcornerpad

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3445-275*

Summary of content (12 pages)

PAGE 1
Form No. 3445-275 Rev A Sound Reducing Kit Groundsmaster® 3200 or 3300 Series Traction Unit with Winter Enclosure Model No.
PAGE 2
Installing the Steering Cover and Steering-Column Plugs 1. Remove the fasteners and lift the steering cover up out of the way (Figure 1). Note: While you install the plugs/pads in this procedure, you can use string to secure the steering cover to the steering wheel. g332885 Figure 3 2. Pressure sensitive adhesive (plug) 1. Backing film 4. Install the upper steering plug (Figure 4). g330592 Figure 1 2. Bolt 1. Steering cover 2.
PAGE 3
g331281 Figure 7 1. Steering plug (PSA) 2. Steering cover (cutaway view shown) g330591 Figure 5 1. Lower steering plug (PSA) 6. Remove the backing film and install the steering pad (Figure 6). g331294 Figure 8 Top view g330645 Figure 6 1. Mounting-tab plugs (PSA) 1. Steering plug 2. Steering pad (PSA) 7. Remove the backing film and install the 3 mounting-tab plugs over holes in floor pan. (Figure 6). 8. Remove the backing film and install the steering plug to the steering cover (Figure 7).
PAGE 4
g330624 g330592 Figure 11 Figure 9 1. Steering cover 1. Corner floor pad (PSA) 2. Bolt Removing the Seat Installing the Floor Pads 1. 2. Center floor pad (PSA) Remove the rubber floor mat (Figure 10). Perform the following steps to remove the seat from the seat base: 1. Remove the nuts that secures the seat to the seat base (Figure 12). Note: Retain the nuts. g331308 Figure 10 1. Rubber floor mat g299346 2.
PAGE 5
Installing the Brake Cover and Plugs 1. 5. Remove the push-in fasteners that secure the brake cover to the floor (Figure 13). • Left side of the brake cover: Cut the plugs. • Right side of the brake cover: Pull the plugs out of the cover and retain the plugs. Remove the backing film from the top of the upper brake-cover foam, and install it to the brake cover (Figure 15). Figure 16 shows a top and cutaway (side) view of the foam installed in the cover. g301501 Figure 13 1. Plugs (4 total—2 shown) 2.
PAGE 6
Installing the Firewall Pads 1. Remove the backing film and install the lower-firewall pad (Figure 17). g331283 Figure 16 1. Top view 3. Upper brake foam (PSA—both sides) 2. Cutaway (side) view 4. Lower brake foam 6. Remove the backing film from the bottom side of the upper brake-cover foam (Figure 15). 7. Install the lower brake-cover foam onto the upper brake-cover foam (Figure 15 and Figure 16). g330760 8. 9. Figure 17 1.
PAGE 7
4. Remove the backing film and install the rear-window pad (Figure 18). Installing the Seat Pads 1. Install the seat-base pad (thin) inside of the seat base (Figure 19). g330729 Figure 19 1. Seat-base pad (thick) 3. Seat base 2. Seat-base pad (thin) 2. 3. Install the seat-base pad (thick) inside of the seat base (Figure 19). g330728 Figure 20 Install the seat pad around the seat base (Figure 20). 1. Seat pad 7 2.
PAGE 8
Installing the Corner Pads 3 Remove the backing film and install the corner pads as shown in Figure 21. Installing the Upper-Frame Components Parts needed for this procedure: 2 Rear-pillar pad 1 Left door-side pad 1 Right door-side pad 1 Upper-ceiling pad 1 Lower-ceiling pad 2 Mount-panel pad 1 Left rear-pillar cover 1 Right rear-pillar cover 1 Left sound-dampening panel 1 Right sound-dampening panel 1 Left outer-pillar pad 1 Right outer-pillar pad g330727 Figure 21 1.
PAGE 9
Figure 27 shows the proper dimensions for installing the outer-pillar pads and sound-dampening panels to the rear-pillar covers. g330652 Figure 24 Left side shown 1. Mount-panel bracket 3. Bolt 2. Rear-side cover 2. Install the rear-pillar pads over the hoses and wire harness (Figure 25). g331296 Figure 26 Left-sided panels/pads shown 1. Sound-dampening panel (PSA) 2. Rear-pillar cover g330647 Figure 25 Left side shown 1. Mount-panel bracket 3. Rear-pillar pad 2. ROPS 3.
PAGE 10
g330646 Figure 28 Left side shown 1. Mount-panel bracket 3. Rear-pillar-cover assembly 2. Rear-pillar pad 4. Bolt Installing the Ceiling Pads 1. g331309 Figure 27 Left-sided panel shown 1. 13.5 mm (0.53 inch) 3. 12.7 mm (0.50 inch) 2. 7.9 mm (0.31 inch) 4. 8.4 mm (0.33 inch) 4. Remove the backing film and install the ROPS pads to the ROPS mounts (Figure 29). Use the previously-removed bolts to install the rear-pillar-cover assembly (i.e.
PAGE 11
Installing the Door-Side Pads Remove the backing film and install the door-side pads as shown in Figure 32. g330650 Figure 30 1. Rear cab window (PSA) 3. 2. Lower-ceiling pad (PSA) Remove the backing film and install the upper-ceiling pad to the ROPS mount bracket (Figure 31). g330683 Figure 32 1. Left door-side pad (PSA) 2. Side panel g330648 Figure 31 1. ROPS mount bracket 2. Upper-ceiling pad (PSA) 11 3.
PAGE 12
Install the Mount-Panel Pads Installing the Rubber Floor Mat Remove the backing film and install the mount-panel pads to the sides of the cab control panel as shown in Figure 33. Assemble the rubber floor mat to the floor of the machine (Figure 35). g330684 Figure 33 1. Cab-control panel g332924 Figure 35 2. Mount-panel pads (PSA) 1. Rubber floor ma 4 Connecting the Battery Connect the battery; refer to the electrical system maintenance section in the Operator’s Manual for your machine.