Installation Instructions

ManualsBrandsToro ManualsRiding ProductsTrimmer Mount Kit, Z Master 4000 Series Riding Mower

FormNo.3442-872RevA

TrimmerMountKit

ZMaster

4000SeriesRidingMower

ModelNo.144-2665

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Uppertrimmermountbracket1

Largestclamp

Largebackerplate1

Carriagebolt(1/4x1-1/2inches)

Flangenut(1/4inch)

Assembletheuppertrimmermount

assembly.

Carriagebolt(5/16x7/8inch)

Flangenut(5/16inch)

Securetheuppertrimmermount

assemblytothesupportbracket.

Supportbracket

Tubespacer2

Carriagebolt(3/8x3inches)

Flangenut(3/8inch)

Installthesupportbracket.

Lowertrimmermountassembly1

Flangenut(3/8inch)

Carriagebolt(3/8x1-1/4inches)—for

machineswiththeBaggerKitinstalled

Hex-headbolt(3/8x1inch)—for

machineswithouttheBaggerKit

installed

Installthelowertrimmermount

assembly.

Trimmermountbracket1

Fist-mountplate1

Smallstclamp

Smallbackerplate

Flangenut(1/4inch)

Carriagebolt(1/4x3/4inch)

Carriagebolt(1/4x1-1/4inches)

Assemblethetrimmermountbracket.

Carriagebolt(1/4x3/4inch)

Flangenut(1/4inch)

Securethetrimmermountbrackettothe

lowertrimmermountassembly.

Nopartsrequired

–

Secureatrimmertothemount

assemblies.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3442-872*

Summary of content (8 pages)

PAGE 1
Form No. 3442-872 Rev A Trimmer Mount Kit Z Master® 4000 Series Riding Mower Model No. 144-2665 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Move the motion-control levers to the NEUTRAL-LOCK position. 3. Engage the parking brake. 4. Shut off the engine and remove the key.
PAGE 3
2 3 Assembling the Upper Trimmer Mount Assembly Securing the Upper Trimmer Mount Assembly to the Support Bracket Parts needed for this procedure: 1 Upper trimmer mount bracket 1 Large fist clamp 1 Large backer plate 2 Carriage bolt (1/4 x 1-1/2 inches) 2 Flange nut (1/4 inch) Parts needed for this procedure: 2 Carriage bolt (5/16 x 7/8 inch) 2 Flange nut (5/16 inch) Procedure Secure the upper trimmer mount assembly to the support bracket using 2 carriage bolts (5/16 x 7/8 inch) and 2 flang
PAGE 4
Installing the Support Bracket Parts needed for this procedure: 1 Support bracket 2 Tube spacer 2 Carriage bolt (3/8 x 3 inches) 2 Flange nut (3/8 inch) Procedure 1. Lower the roll bar. 2. Install the support bracket to the right post of the roll bar using 2 tube spacers, 2 carriage bolts (3/8 x 3 inches), and 2 flange nuts (3/8 inch) as shown in Figure 4. 3. Slowly raise the roll bar and ensure that there is no interference between the roll bar and support bracket.
PAGE 5
side of the frame using 2 carriage bolts (3/8 x 1-1/4 inches) or 2 hex-head bolts (3/8 x 1 inch) and 2 flange nuts (3/8 inch) as shown in Figure 6. 5 Installing the Lower Trimmer Mount Assembly Parts needed for this procedure: 1 Lower trimmer mount assembly 2 Flange nut (3/8 inch) 2 Carriage bolt (3/8 x 1-1/4 inches)—for machines with the Bagger Kit installed 2 Hex-head bolt (3/8 x 1 inch)—for machines without the Bagger Kit installed g337882 Figure 6 Carriage bolt installation shown 1.
PAGE 6
Assembling the Trimmer Mount Bracket Parts needed for this procedure: 1 Trimmer mount bracket 1 Fist-mount plate 1 Small fist clamp 1 Small backer plate 4 Flange nut (1/4 inch) 2 Carriage bolt (1/4 x 3/4 inch) 2 Carriage bolt (1/4 x 1-1/4 inches) Procedure Assemble the trimmer mount bracket (Figure 7). g248809 Figure 7 1. Flange nut (1/4 inch) 5. Carriage bolt (1/4 x 1-1/4 inches) 2. Small backer plate 6. Trimmer mount bracket 3. Small fist clamp 7. Carriage bolt (1/4 x 3/4 inch) 4.
PAGE 7
8 Securing the Trimmer Securing a Trimmer to the Mount Bracket to the Lower Mount Assemblies Trimmer Mount Assembly No Parts Required Parts needed for this procedure: 2 Carriage bolt (1/4 x 3/4 inch) 2 Flange nut (1/4 inch) Procedure Insert the handle end of the trimmer into the large fist clamp and the trimming end into the small fist clamp. Check the fit of the trimmer for interference, and adjust the mounting hole locations as required for clearance to the machine.
PAGE 8