Form No. 3445-921 Rev C 软管更换组件 Groundsmaster® 3200 或 3300 系 列 主 机 型 号 144-3960 安装说明 安装 散装零件 使用下表进行核对 确保所有零件已装运。 说明 数量 不需要零件 – 右冷却器护罩支架 左冷却器护罩支架 凸缘螺母 5/16 英寸 软管导向架 扁平垫圈 5/16 英寸 直通接头 90°弯头 带直通接头的软管 带 90°弯头的软管 右冷却器护罩支架组件 盖子 尼龙锁紧螺母⅜ 英寸 螺栓 ⅜ x 3 英寸 扁平垫圈 ⅜ 英寸 直通接头 90°弯头 带直通接头的软管 带 90°弯头的软管 左冷却器护罩支架组件 软管导向架 盖子 尼龙锁紧螺母⅜ 英寸 螺栓 ⅜ x 3 英寸 扁平垫圈 ⅜ 英寸 1 1 4 2 4 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 2 1 1 1 准备机器 1. 将机器停在水平地面上。 2. 接合驻车刹车。 3. 放低滚刀组。 4. 关闭发动机并拔下钥匙。 5. 用途 准备机器。 将软管导向架安装到冷却器护罩支架。 安装右侧软管。 安装左侧软管。 6.
将软管导向架安装到冷却器 护罩支架 使用 2 个扁平垫圈5/16 英寸和 2 个凸缘螺母5/16 英寸将软管导向架安装到左右冷却器护罩支架请参 阅图 1。 g359126 图1 1. 左冷却器护罩支架 4. 软管导向架 2. 凸缘螺母5/16 英寸 5. 右冷却器护罩支架 3. 扁平垫圈5/16 英寸 g360588 图3 1. 3. 安装右侧软管 盖子 2. 液压管线 将新的直通接头和 90°弯头安装到车轮马达上 图 4。 注 意 每次安装 1 侧。 1. 从车轮前面的液压管线上拆下现有的液压软 管并立即将盖子安装到液压管线上图 2和图 3。 g368201 图2 1. 2. 现有软管 2. 液压管线 从车轮马达上拆下现有的软管接头。 g364926 图4 2 1. 带直通接头的软管 4. 90°弯头 2. 液压管线 5. 3.
4. 将 90°弯头调整到 15°角如图 5所示。 g359115 图5 1. 15°适用于带直通接头的 软管 2. 20°适用于带 90°弯头的软 管 5. 上紧车轮马达接头扭矩至 142 N∙m。 6. 将带直通接头的软管安装到 90°弯头图 4。 7. 将带 90°弯头的软管安装到直通接头图 4。 8. 将 90°软管弯头调整到 20°如图 5所示。 9. 将软管连接到接头上上紧扭矩至 57 N∙m。 g360591 图6 1. 凸缘螺母 ⅜ 英寸 2. 扁平垫圈⅜ 英寸 3. 螺栓⅜ x 3 英寸 注 意 确保维持角度如图 5所示。 10. 11. 拆下散热器下方固定减震器支架的现有螺母和 螺栓 图 6 。 12. 松开散热器侧的螺栓图 7。 13. 将冷却器护罩支架滑到散热器和缓冲器支架的 螺栓头下方 图 7 。 用螺栓⅜ x 3 英寸、扁平垫圈⅜ 英寸和凸缘螺 母⅜ 英寸将现有的螺母和螺栓重新安装到支架 上。在安装冷却器护罩支架之前不要拧紧螺栓。 g360593 图7 1. 14. 3 冷却器护罩支架 2.
15. 将软管穿过软管导向架图 8。 g360590 图8 1. 16. 安装软管并穿过导向架 一次拆下一个盖子并将正确的软管安装到液压 管线上 如图 4所示。 注 意 使用支撑扳手防止软管扭曲。 17. 拆下剩余的盖子并将软管安装到液压管线上图 4。 18. 将软管连接到液压管线上上紧扭矩至 85 N∙m。 g359336 图 10 1. 注 意 确保软管上下对齐而不是侧面对齐。 19. 安装后轮并确保软管和轮胎侧壁之间有 1.6mm 到 4.8mm 的间隙。 20. 如果间隙大小不正确请使用 90°弯头或 90°接 头调整软管。 21. 3. 盖子 2. 液压管线 将新的直通接头和 90°弯头安装到车轮马达上 图 11 。 拧紧车轮螺母有关正确的程序请参阅 操作员 手册 。 安装左侧软管 1. 从车轮前面的液压管线上拆下现有的液压软管并 立即将盖子安装到液压管线上图 9和图 10。 g359303 图 11 g368212 图9 1. 2. 现有软管 2. 液压管线 1. 带 90°弯头的软管 4. 直通接头 2.
g359115 图 12 1. 15°适用于带直通接头的 软管 2. 20°适用于带 90°弯头的软 管 5. 上紧车轮马达接头扭矩至 142 N∙m。 6. 将带直通接头的软管安装到 90°弯头图 11。 7. 将带 90°弯头的软管安装到直通接头图 11。 8. 将 90°软管弯头调整到 20°如图 12所示。 9. 将软管连接到接头上上紧扭矩至 57 N∙m。 注 意 确保维持角度如图 12所示。 10. 拆下散热器下方固定减震器支架的现有螺母和 螺栓 图 13 。 11. 用螺栓⅜ x 3 英寸、扁平垫圈⅜ 英寸和凸缘螺 母⅜ 英寸将现有的螺母和螺栓重新安装到支架 上。在安装冷却器护罩支架之前不要拧紧螺栓。 g359304 图 13 1. 凸缘螺母 ⅜ 英寸 2. 扁平垫圈⅜ 英寸 3. 螺栓⅜ x 3 英寸 12. 松开散热器侧的螺栓图 14。 13. 将左冷却器护罩支架组件滑到散热器和缓冲器 支架的螺栓头下方图 14。 g359305 图 14 1. 5 冷却器护罩支架 2. 螺栓头 14.
g359337 图 15 1. 16. 安装软管并穿过导向架 一次拆下一个盖子并将正确的软管安装到液压 管线上如图 11所示。 注 意 使用支撑扳手防止软管扭曲。 17. 拆下剩余的盖子并将软管安装到液压管线上图 11 。 18. 将软管连接到液压管线上上紧扭矩至 85 N∙m。 注 意 确保软管上下对齐而不是侧面对齐。 19. 安装后轮并确保软管和轮胎侧壁之间有 1.6mm 到 4.8mm 的间隙。 20. 如果间隙大小不正确请使用 90°弯头或 90°接 头调整软管。 21. 拧紧车轮螺母有关正确的程序请参阅 操作员 手册 。 22. 降下机罩并将其锁上。 23. 降下机器的后部。 24. 缓慢向前和向后驾驶机器以清除牵引系统中的 空气。 25. 检查接头连接和软管是否有任何泄漏。 26.
备注