Installation Instructions

ManualsBrandsToro ManualsRiding ProductsSeat Kit, Serial Number 406999999 and Before Sand Pro 2040Z Traction Unit with Seat Isolation Kit installed

FormNo.3446-649RevA

SeatKit

SerialNumber406999999andBeforeSandPro

2040ZTraction

UnitwithSeatIsolationKitinstalled

ModelNo.144-7067

InstallationInstructions

Installation

OrderingtheServiceDecal

Partsneededforthisprocedure:

ServiceDecal(refertothePartsCatalogforyour

machine)

Procedure

Obtainanewservicedecalforyourmachinefroman

authorizedTorodistributorbeforeinstallingtheseat

replacementkit;refertothePartsCatalogforyour

machine.

PreparingtheMachine

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurfaceandlower

allattachments.

2.Engagetheparkingbrake.

3.Shutofftheengineandremovethekey.

4.Waitforallmovingpartstostopbeforeleaving

theoperator’sseat.

RemovingtheSeat

NoPartsRequired

Procedure

1.Removethe4ange-headcapscrews(5/16x1

inch)and4washers(5/16inch)thatsecurethe

seatisolatortothemachine(Figure1).

Note:Discardthecapscrewsandwashers.

g363342

Figure1

1.Flange-headcapscrew

(5/16x1inch)

2.Seatisolator

2.Tilttheseattoaccessthebottomoftheseat

(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3446-649*

Summary of content (4 pages)

PAGE 1
Form No. 3446-649 Rev A Seat Kit Serial Number 406999999 and Before Sand Pro® 2040Z Traction Unit with Seat Isolation Kit installed Model No. 144-7067 Installation Instructions 3 Installation 1 Removing the Seat Ordering the Service Decal Parts needed for this procedure: 1 Service Decal (refer to the Parts Catalog for your machine) No Parts Required Procedure 1. Remove the 4 flange-head capscrews (5/16 x 1 inch) and 4 washers (5/16 inch) that secure the seat isolator to the machine (Figure 1).
PAGE 2
4 Replacing the Clip Nuts Parts needed for this procedure: 8 g363343 Clip nut (5/16 inch) Figure 2 1. Push-in harness tie 3. 2-socket connector (machine wire harness) Procedure 1. 2. 2-pin connector (operator-presence switch) Remove the 8 clip nuts (5/16 inch) from the left and right seat brackets (Figure 4). Note: Discard the old clip nuts. 3. Remove the 2-socket connector of the machine wire harness from the 2-pin connector of the operator-presence switch. 4.
PAGE 3
g362546 Figure 5 1. Seat base 2. 2. Maintenance decal Remove the backing from the maintenance decal, and adhere the decal to the seat base as shown in Figure 5. 3. g363339 Figure 7 Insert the push-in harness tie in the hole in the seat base as shown in Figure 6. 1. Flange-head capscrews (5/16 x 1 inch) 3. Clip nuts 2. Seat isolator Assembling the Seat to the Machine 1. Carefully lower the new seat onto the machine. g362544 Figure 6 1. Hole (seat base) 2.
PAGE 4
7 Testing the Operator’s Presence Switch No Parts Required g362548 Procedure Figure 9 1. Push-in harness tie 3. 2-socket connector (machine wire harness) 2. 2-pin connector (operator-presence switch) 3. Plug the 2-socket connector of the machine wire harness into the 2-pin connector of the operator-presence switch. 1. Sit in the operator's seat, ensure the traction controls are in the NEUTRAL position, and the parking brake is engaged. 2. Start the engine. 3.